doing my swivel hubs/bearing and put the bearing race thingo in the wrong way and now it wont come out. any creative ideas of getting the bastard out? was a mistake of not checking which way the bearing would sit
car is a 87 sierra
| auszookers.com https://auszookers.com/forum/ |
|
| errr put the bearing race thingo in backwards https://auszookers.com/forum/viewtopic.php?f=5&t=16801 |
Page 1 of 1 |
| Author: | needmorelift [ Mon Nov 15, 2010 10:17 am ] |
| Post subject: | errr put the bearing race thingo in backwards |
doing my swivel hubs/bearing and put the bearing race thingo in the wrong way and now it wont come out. any creative ideas of getting the bastard out? was a mistake of not checking which way the bearing would sit
car is a 87 sierra |
|
| Author: | royce [ Mon Nov 15, 2010 10:27 am ] |
| Post subject: | Re: errr put the bearing race thingo in backwards |
Ask Bruce 
if you get a brass drift (or anything softer than the race, wood will do and place it against one side horizontal and tap it with a hammer then the other side and work back and forward it will work its way out |
|
| Author: | needmorelift [ Mon Nov 15, 2010 10:36 am ] |
| Post subject: | Re: errr put the bearing race thingo in backwards |
cheers royce but i got it sorted using the stekky method...if a hammer doesnt work...get a bigger one 
|
|
| Author: | shep [ Mon Nov 15, 2010 7:58 pm ] |
| Post subject: | Re: errr put the bearing race thingo in backwards |
hahahahaha. hay how come all the phones on elcho have stopped working since 2jays was here? |
|
| Author: | needmorelift [ Mon Nov 15, 2010 8:00 pm ] |
| Post subject: | Re: errr put the bearing race thingo in backwards |
your net still works so what are you complaining about 
|
|
| Author: | shep [ Mon Nov 15, 2010 8:04 pm ] |
| Post subject: | Re: errr put the bearing race thingo in backwards |
only about %20 of the time. it shows full signal but wont transmit stuff. not just me either, everybody is affected. |
|
| Author: | needmorelift [ Mon Nov 15, 2010 8:20 pm ] |
| Post subject: | Re: errr put the bearing race thingo in backwards |
oh ok i'll ring him today and ask him. |
|
| Author: | shep [ Mon Nov 15, 2010 8:29 pm ] |
| Post subject: | Re: errr put the bearing race thingo in backwards |
thanks mate, just tell him if he fixes it i will show him where the 40 series toyotas are hidden |
|
| Author: | needmorelift [ Tue Nov 16, 2010 12:41 am ] |
| Post subject: | Re: errr put the bearing race thingo in backwards |
he says he chopped it cos you wouldnt show him the 40s lol nah he doesn't know why its not working. have you rung up them telstra call centres? |
|
| Author: | shep [ Tue Nov 16, 2010 12:44 am ] |
| Post subject: | Re: errr put the bearing race thingo in backwards |
needmorelift wrote: he says he chopped it cos you wouldnt show him the 40s lol
nah he doesn't know why its not working. have you rung up them telstra call centres? haha no one can ring a call center because the phones drop out every 5 min and ya need to wait on hold for half a life time. 
|
|
| Author: | steak_knife [ Tue Nov 16, 2010 5:41 am ] |
| Post subject: | Re: errr put the bearing race thingo in backwards |
needmorelift wrote: cheers royce but i got it sorted using the stekky method...if a hammer doesnt work...get a bigger one
  peaceout
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|