auszookers.com
https://auszookers.com/forum/

wheel berrings
https://auszookers.com/forum/viewtopic.php?f=5&t=16813		 Page 1 of 1
Author:  TryHard [ Tue Nov 16, 2010 12:06 am ]
Post subject:  wheel berrings
hey also sometimes when i dry turn i here a clicking kinda noise i think my wheel bearings need done but iv have never done wheel bearings before how hard are they to do ? thanks and what do i need and what involved .. i know i have to take my hub off etc ... thanks
Author:  BlueSuzy [ Tue Nov 16, 2010 12:09 am ]
Post subject:  Re: wheel berrings
Clicking sounds like a cv.
Author:  TryHard [ Tue Nov 16, 2010 12:13 am ]
Post subject:  Re: wheel berrings
BlueSuzy wrote:
Clicking sounds like a cv.



should i do my wheel bearings at the same time ?

also do u think if they are clicking i should replace them ..how long do u think they can hang in there
Author:  shep [ Tue Nov 16, 2010 12:16 am ]
Post subject:  Re: wheel berrings
no fix just replace. have a look here as there is a good write up from mud pig.
http://auszookers.com/index.php?name=Ne ... c=2&page=2
Author:  shep [ Tue Nov 16, 2010 12:17 am ]
Post subject:  Re: wheel berrings
when the wheel bearings fail ya wheel will fall off so how far ya push it is up to you.
Author:  TryHard [ Tue Nov 16, 2010 12:18 am ]
Post subject:  Re: wheel berrings
shep wrote:
when the wheel bearings fail ya wheel will fall off so how far ya push it is up to you.


yer iv seen a wheel fall off lol not good at all
Author:  TryHard [ Tue Nov 16, 2010 12:22 am ]
Post subject:  Re: wheel berrings
shep wrote:
no fix just replace. have a look here as there is a good write up from mud pig.
http://auszookers.com/index.php?name=Ne ... c=2&page=2


perfect link thanks very much :)
Author:  shep [ Tue Nov 16, 2010 12:25 am ]
Post subject:  Re: wheel berrings
TryHard wrote:
shep wrote:
no fix just replace. have a look here as there is a good write up from mud pig.
http://auszookers.com/index.php?name=Ne ... c=2&page=2


perfect link thanks very much :)


no worries. there is a fair bit of stuff in the tech articles. :wink: :D
Author:  Hybrid [ Tue Nov 16, 2010 12:46 am ]
Post subject:  Re: wheel berrings
With only a slight thread derailment, what size in the socket needed for the wheel bearing nut? I'm sick of using my hand made socket.
Author:  Damo [ Tue Nov 16, 2010 12:49 am ]
Post subject:  Re: wheel berrings
Hybrid wrote:
With only a slight thread derailment, what size in the socket needed for the wheel bearing nut? I'm sick of using my hand made socket.


50mm from memory. The one I have is a 3/4" drive so you need to use a 3/4" -> 1/2" drive adapter so You can get it on the torque wrench. Works fine though.
Author:  shep [ Tue Nov 16, 2010 1:13 am ]
Post subject:  Re: wheel berrings
yeah 50mm. i have a 1/2" drive lowrange jobbie.
Author:  Hybrid [ Tue Nov 16, 2010 1:40 am ]
Post subject:  Re: wheel berrings
Cool. Glenfords had some bigger than that the other day. Same deal with 3/8" drive though. Might compare the diff in cost to lowrange.
Author:  shep [ Tue Nov 16, 2010 2:19 am ]
Post subject:  Re: wheel berrings
ya need a deepish socket as well
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/