89_tintop wrote:
hey stekky ... to do a wheel bearing on one do you need a special tool? my drivers side has some play in it.
Yer, me...
It's a cassete, so c'lip & hammer/pres out & in, no adjustment..
| auszookers.com https://auszookers.com/forum/ |
|
| 2000 jimny cv?? https://auszookers.com/forum/viewtopic.php?f=5&t=17686 |
Page 1 of 1 |
| Author: | dangerousdog [ Wed Dec 22, 2010 6:37 am ] |
| Post subject: | 2000 jimny cv?? |
well i get to keep my jimny now that i got my mony back for the jeep and i was so looking forward to going out over xmas but now theres some play in the frunt left hub and when i tern it makes a rubbing sound and if i tern going back its sort of a clunk do you think its a cv or bearing |
|
| Author: | steak_knife [ Wed Dec 22, 2010 6:54 am ] |
| Post subject: | Re: 2000 jimny cv?? |
Swivel or wheel bearing, highly doubt the cv will make noise like that |
|
| Author: | 89_tintop [ Wed Dec 22, 2010 7:01 am ] |
| Post subject: | Re: 2000 jimny cv?? |
hey stekky ... to do a wheel bearing on one do you need a special tool? my drivers side has some play in it. |
|
| Author: | steak_knife [ Wed Dec 22, 2010 7:08 am ] |
| Post subject: | Re: 2000 jimny cv?? |
89_tintop wrote: hey stekky ... to do a wheel bearing on one do you need a special tool? my drivers side has some play in it.
Yer, me...
It's a cassete, so c'lip & hammer/pres out & in, no adjustment.. |
|
| Author: | dangerousdog [ Wed Dec 22, 2010 8:30 am ] |
| Post subject: | Re: 2000 jimny cv?? |
so if i pull the hub off ill be able to see if its the bearings |
|
| Author: | steak_knife [ Wed Dec 22, 2010 9:16 am ] |
| Post subject: | Re: 2000 jimny cv?? |
jack it up, put it on stand's & get someone to wobble the wheel, climb under & see if the disc is wobbling with the wheel or if the hole swivel hub is.. If you take the locking hub off you will be able to see the stub axle staying still & the hub moving, but that are a cassette bearing & can't be adjusted.. |
|
| Author: | 89_tintop [ Wed Dec 22, 2010 6:44 pm ] |
| Post subject: | Re: 2000 jimny cv?? |
what does the wheel bearing tool undo?? just searching egay and came across it. |
|
| Author: | Relic [ Wed Dec 22, 2010 8:34 pm ] |
| Post subject: | Re: 2000 jimny cv?? |
i got one of the bearing tools, they just help remove the bearing cartridge, as it only has the holes for the tool and not a large hex nut like other forbys have |
|
| Author: | dangerousdog [ Wed Dec 22, 2010 10:17 pm ] |
| Post subject: | Re: 2000 jimny cv?? |
ok so it looks like the disk is wobbling with the wheel but now there's only a little bit of a rubbing sound coming from it not like last night it seemed a lot louder |
|
| Author: | dangerousdog [ Wed Dec 22, 2010 11:08 pm ] |
| Post subject: | Re: 2000 jimny cv?? |
just riped the hub off and there is a lot of play in the stub axle so what bearing do i need wheel? (think its ment to have a bit of play in it so ill pull some more off) |
|
| Author: | dangerousdog [ Wed Jan 05, 2011 7:28 am ] |
| Post subject: | Re: 2000 jimny cv?? |
well still havent fixed my car need to get one of these http://cgi.ebay.com.au/Suzuki-Jimny-whe ... 19c22f39ea anyone got one ?? or are there any in aust ?? thanks |
|
| Author: | BertZook [ Fri Jan 07, 2011 3:47 am ] |
| Post subject: | Re: 2000 jimny cv?? |
dangerousdog wrote: well still havent fixed my car need to get one of these
http://cgi.ebay.com.au/Suzuki-Jimny-whe ... 19c22f39ea anyone got one ?? or are there any in aust ?? thanks http://auszookers.com/index.php?name=Fo ... ic&t=15009 
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|