well I have done the drivers ide and rewelded got it out 60 mm on both sides so it should fit according to the tape measure
joe and gwagen have me a bit worried about the no body lift and 1.6 and auto though.
| auszookers.com https://auszookers.com/forum/ |
|
| 3 speed auto sierra https://auszookers.com/forum/viewtopic.php?f=5&t=18018 |
Page 1 of 1 |
| Author: | ajsr [ Wed Jan 05, 2011 9:11 am ] |
| Post subject: | 3 speed auto sierra |
can anyone tell me how much wider the trans tunnel needs to become for the auto to fit comfortably?? pics are good too if you have them cheers |
|
| Author: | Rusho [ Wed Jan 05, 2011 6:17 pm ] |
| Post subject: | Re: 3 speed auto sierra |
Fatzook is in the process of widening his tunnel also. He is doing vit manual, however he made a template off Matt's ute which has the auto. At a guess there would be at least 60-80mm off each side and cut out almost the whole way up, then just plated back up if that makes sense??? |
|
| Author: | got_bar_work [ Wed Jan 05, 2011 7:47 pm ] |
| Post subject: | Re: 3 speed auto sierra |
Just go get a vit tunnel and weld it in A guy in the club has done this and it looks good |
|
| Author: | dank [ Wed Jan 05, 2011 11:05 pm ] |
| Post subject: | Re: 3 speed auto sierra |
hey AJ, my application is a little different but to fit the corolla 3 spd in I had to stretch the tunnel on the passenger side out by around 40mm and about 20mm on the drivers side to clear the sump pan. |
|
| Author: | Fatzook [ Wed Jan 05, 2011 11:29 pm ] |
| Post subject: | Re: 3 speed auto sierra |
Assuming the pan and lines etc on the 3sp take up the same amount of room as the 4sp, I'd say a good 50mm per side, and back to where the floor steps up in the height from the footwell. I'll get a pic of my floor for you. Its all marked out ready to cut. |
|
| Author: | tanshi [ Wed Jan 05, 2011 11:46 pm ] |
| Post subject: | Re: 3 speed auto sierra |
i cut about 30mm out of passanger side for my manual. |
|
| Author: | ajsr [ Thu Jan 06, 2011 7:15 am ] |
| Post subject: | Re: 3 speed auto sierra |
well I have done the drivers ide and rewelded got it out 60 mm on both sides so it should fit according to the tape measure
joe and gwagen have me a bit worried about the no body lift and 1.6 and auto though. |
|
| Author: | shep [ Thu Jan 06, 2011 7:28 am ] |
| Post subject: | Re: 3 speed auto sierra |
ajsr wrote: joe and gwagen have me a bit worried about the no body lift and 1.6 and auto though. ppffffttttt what would they know  
|
|
| Author: | Fatzook [ Thu Jan 06, 2011 7:42 am ] |
| Post subject: | Re: 3 speed auto sierra |
ajsr wrote: joe and gwagen have me a bit worried about the no body lift and 1.6 and auto though. Why? I got a 1.6 and auto under a 1L bonnet with no BL. Surely you can do it with a 1.3L bonnet
|
|
| Author: | ajsr [ Thu Jan 06, 2011 7:53 am ] |
| Post subject: | Re: 3 speed auto sierra |
Fatzook wrote: ajsr wrote: joe and gwagen have me a bit worried about the no body lift and 1.6 and auto though. Why? I got a 1.6 and auto under a 1L bonnet with no BL. Surely you can do it with a 1.3L bonnet vit/x90 1.6 ??? |
|
| Author: | Fatzook [ Thu Jan 06, 2011 7:54 am ] |
| Post subject: | Re: 3 speed auto sierra |
ajsr wrote: Fatzook wrote: ajsr wrote: joe and gwagen have me a bit worried about the no body lift and 1.6 and auto though. Why? I got a 1.6 and auto under a 1L bonnet with no BL. Surely you can do it with a 1.3L bonnet vit/x90 1.6 ??? X-90 
Build: Work Horse |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|