pull the gear box back as far as possible and let the front of the box down it may hit the pressure plate but you should be able to get it past
trty this let me know how you go 
| auszookers.com https://auszookers.com/forum/ |
|
| changing clutch https://auszookers.com/forum/viewtopic.php?f=5&t=18390 |
Page 1 of 1 |
| Author: | cairns27 [ Thu Jan 20, 2011 6:17 am ] |
| Post subject: | changing clutch |
hey is the chasie built around the gearbox it just woun't come out ...........the fan is aagainst the radiator, I have heard of doing it by rotating the box, but naa I know I shouldn't start another thread but it was nothing like thed preceding changing clutch thread I hav't even mentioned the wires that hang persistantly to the top of the fuck'n thing It's the nephew's car and he's with me occassionaly' but not when needed All help welcomed Thanking you in anticipation |
|
| Author: | alex [ Thu Jan 20, 2011 6:32 am ] |
| Post subject: | Re: changing clutch |
pull the gear box back as far as possible and let the front of the box down it may hit the pressure plate but you should be able to get it past trty this let me know how you go
|
|
| Author: | cairns27 [ Thu Jan 20, 2011 7:13 am ] |
| Post subject: | need help badly |
kindly to please read the thread on changing clutch, gearbox just does not come out tar |
|
| Author: | Ben_Sierra [ Thu Jan 20, 2011 7:16 am ] |
| Post subject: | Re: need help badly |
When someone has an answer they will give it too you... There is no need to keep posting 
|
|
| Author: | atari4x4 [ Thu Jan 20, 2011 7:17 am ] |
| Post subject: | Re: need help badly |
would help if you keep it all in one thread...
http://auszookers.com/index.php?name=Fo ... ic&t=18390 have you tried what alex suggested? |
|
| Author: | boostedbrick [ Thu Jan 20, 2011 7:20 am ] |
| Post subject: | Re: changing clutch |
what is it in? |
|
| Author: | cairns27 [ Thu Jan 20, 2011 7:22 am ] |
| Post subject: | Re: changing clutch |
did that, even jacked the back of the engine up......1 or2mm in it |
|
| Author: | cairns27 [ Thu Jan 20, 2011 7:26 am ] |
| Post subject: | Re: changing clutch |
sorry...............it's a '93 swb serria |
|
| Author: | boostedbrick [ Thu Jan 20, 2011 7:29 am ] |
| Post subject: | Re: changing clutch |
In mine i need to remove the front driveshaft because of my exhuast location. then turn and twist it to the left... Just scrapes the pressure plate. And if you putting a new clutch in, it wont matter if you damage the pressure plate... |
|
| Author: | steak_knife [ Thu Jan 20, 2011 7:45 am ] |
| Post subject: | Re: changing clutch |
cairns27 wrote: did that, even jacked the back of the engine up......1 or2mm in it
Try jacking the front up... |
|
| Author: | cairns27 [ Thu Jan 20, 2011 8:09 am ] |
| Post subject: | Re: changing clutch |
ok i'll jack the front of the engine up in the morning.....took the front drive sharft off....guess I'll jack front up after I drop front of box...broke exhaust near transfer case, and pulls aside |
|
| Author: | steak_knife [ Thu Jan 20, 2011 8:17 am ] |
| Post subject: | Re: changing clutch |
They DO fit out, it a lil bit of a pain, but with luck you shouldn't havae to do it again for a while.. Have you removed the G/box mount & bracket off the g/box?? Make's a big difference.. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|