| auszookers.com https://auszookers.com/forum/ |
|
| Vitara twin transfer kit https://auszookers.com/forum/viewtopic.php?f=5&t=18578 |
Page 1 of 1 |
| Author: | want33s [ Wed Jan 26, 2011 9:30 pm ] |
| Post subject: | Vitara twin transfer kit |
Anyone got a link for manufacture/purchase of Vitara twin transfers or just the adaptor? |
|
| Author: | Fatzook [ Wed Jan 26, 2011 9:46 pm ] |
| Post subject: | Re: Vitara twin transfer kit |
OTT Kicker 3 doubler Use your sierra case.... OTT |
|
| Author: | want33s [ Wed Jan 26, 2011 9:51 pm ] |
| Post subject: | Re: Vitara twin transfer kit |
Fatzook wrote:
Want to use TWO Vit transfers...... Need central rear output. |
|
| Author: | Fatzook [ Wed Jan 26, 2011 10:00 pm ] |
| Post subject: | Re: Vitara twin transfer kit |
Im not aware of any that use 2 vit cases. There are a few that use a vita and a toy case, so you still get the centre output. Also others that convert to W56 or similar with marllin twin toy cases, but I've not seen a twin vit case kit thats off the shelf. The OTT kicker 2 uses a modded vit case with an adaptor to toy transfer. Probably the closest you will get without custom making it. 
|
|
| Author: | got_bar_work [ Thu Jan 27, 2011 12:20 am ] |
| Post subject: | Re: Vitara twin transfer kit |
I have seen a few but cant remember where U have to cut the front output shaft off the old case and have a plate tiged over the hole then I think they bolt together with just a splined coupler between them Have a look on zukiworld there are a few people on there with them Wat r u going to do about high range |
|
| Author: | want33s [ Thu Jan 27, 2011 3:03 am ] |
| Post subject: | Re: Vitara twin transfer kit |
got_bar_work wrote: Wat r u going to do about high range
5.12 diffs will help. I'll be running 35" tyres so can always put one case in low if needed... I don't drive on the road and max speed in the bush is 70 km/h or so. |
|
| Author: | v6zookie [ Thu Jan 27, 2011 6:41 am ] |
| Post subject: | Re: Vitara twin transfer kit |
Do u mean vit then the serria box |
|
| Author: | Ben_Sierra [ Thu Jan 27, 2011 6:44 am ] |
| Post subject: | Re: Vitara twin transfer kit |
v6zookie wrote: Do u mean vit then the serria box want33s wrote: Fatzook wrote: Want to use TWO Vit transfers...... Need central rear output. |
|
| Author: | tombutt [ Thu Jan 27, 2011 6:50 am ] |
| Post subject: | Re: Vitara twin transfer kit |
if you make it work want 33's take pictures and tell me how may be handy when i go bigger tyres |
|
| Author: | Teracis [ Thu Jan 27, 2011 6:53 am ] |
| Post subject: | Re: Vitara twin transfer kit |
How good it would be to have a second high/low lever! Pity they are so expensive! One would still have to stop to change one of these between ranges yes? |
|
| Author: | want33s [ Thu Jan 27, 2011 6:56 am ] |
| Post subject: | Re: Vitara twin transfer kit |
Teracis wrote: How good it would be to have a second high/low lever!
Pity they are so expensive! One would still have to stop to change one of these between ranges yes? Yes, no synchros in a transfer means a stop is necessary to shift between ranges. |
|
| Author: | royce [ Thu Jan 27, 2011 7:46 am ] |
| Post subject: | Re: Vitara twin transfer kit |
http://www.pirate4x4.com/forum/showthre ... ker+to+toy kicker 2 goes modded vitara to toyota joeblow might like to add something on the possibility of dual vit cases, the removal of the front output is well known now so another transfer on the back might be possible |
|
| Author: | Brett [ Thu Jan 27, 2011 7:47 am ] |
| Post subject: | Re: Vitara twin transfer kit |
what about the guy on here putting the v6 in a sierra and he has used a lux transfer case on a vitara box because its a bolt up. you could just use a twin kit for a lux then. don't know if its the same box between the 1.6 and 2.5 only other way i can think of is how joe cuts them for twins in a sierra but you make it so a stock tcase bolts up to the cut tcase |
|
| Author: | Teracis [ Thu Jan 27, 2011 8:17 am ] |
| Post subject: | Re: Vitara twin transfer kit |
want33s wrote: Teracis wrote: How good it would be to have a second high/low lever! Pity they are so expensive! One would still have to stop to change one of these between ranges yes? Yes, no synchros in a transfer means a stop is necessary to shift between ranges. Yeh I realised that, just wasn't sure if it was some form of gearbox addition then I realised it's just a second transfer case that goes between the gearbox and the original transfer case. Still, provided you had 1:1 for high range (unless you wanted permanent reduction) then you would only be gaining extra range! |
|
| Author: | want33s [ Thu Jan 27, 2011 11:07 pm ] |
| Post subject: | Re: Vitara twin transfer kit |
Brett wrote: what about the guy on here putting the v6 in a sierra and he has used a lux transfer case on a vitara box because its a bolt up. you could just use a twin kit for a lux then.
don't know if its the same box between the 1.6 and 2.5 Got a link to that thread Brett? That might be the way to go. Would also save the drama of the Vit front output being the slip joint. I just rang OTT in Canada and they aren't making any Kicker setups for 2-3 months as they are downsizing factories and have been hit hard by the "GFC" 
|
|
| Author: | royce [ Thu Jan 27, 2011 11:12 pm ] |
| Post subject: | Re: Vitara twin transfer kit |
http://www.auszookers.com/index.php?nam ... pic&t=9848 V6 box differs to teh 1.6 box though, guess youll have to fit a 2.5 now 
|
|
| Author: | RIKSTR [ Fri Jan 28, 2011 12:46 am ] |
| Post subject: | Re: Vitara twin transfer kit |
You could also look at the Trail Tough "Undertaker" as a good bolt in solution Undertaker |
|
| Author: | want33s [ Fri Jan 28, 2011 5:50 am ] |
| Post subject: | Re: Vitara twin transfer kit |
RIKSTR wrote:
$1295 
Looks like a possible solution... The other problem I have is eliminating the slip joint from the front output. In the picture below from the undertaker link is a bolt on flange but Trail Tough don't list it.... Any ideas??? 
I have a mate that runs a CNC lathe and mill for a living, might talk to him about mating hilux (ewww wash my mouth out) transfer to Vitara box which gives me more gearing or twin transfer options down the track. |
|
| Author: | Fatzook [ Fri Jan 28, 2011 6:13 am ] |
| Post subject: | Re: Vitara twin transfer kit |
want33s wrote: In the picture below from the undertaker link is a bolt on flange but Trail Tough don't list it.... Any ideas???.
Slip yolk eliminator |
|
| Author: | want33s [ Fri Jan 28, 2011 6:30 am ] |
| Post subject: | Re: Vitara twin transfer kit |
Fatzook wrote: want33s wrote: In the picture below from the undertaker link is a bolt on flange but Trail Tough don't list it.... Any ideas???. Slip yolk eliminator "Works on 91+ models" That'd be right I have an 89 transfer.... Pete you still got the transfer I gave you with the gearbox?
|
|
| Author: | Fatzook [ Fri Jan 28, 2011 6:32 am ] |
| Post subject: | Re: Vitara twin transfer kit |
yep. Come get it  I tripped over it last night, soyou had better be quick or it will be landfill 
|
|
| Author: | want33s [ Fri Jan 28, 2011 6:35 am ] |
| Post subject: | Re: Vitara twin transfer kit |
Awesome.  .. Will try to get down there by mid next week.. Will call to arrange a time.
|
|
| Author: | tombutt [ Fri Jan 28, 2011 6:39 am ] |
| Post subject: | Re: Vitara twin transfer kit |
want33s wrote: Awesome.
.. Will try to get down there by mid next week.. Will call to arrange a time.mate you can take your time last time he said he needed to go to the dump it took him almost a month to actually go plus he doesnt have the ute or a tow ball on the vit |
|
| Author: | Fatzook [ Fri Jan 28, 2011 6:39 am ] |
| Post subject: | Re: Vitara twin transfer kit |
cool. I'll empty the water out of it. JK
|
|
| Author: | 5ierra [ Fri Jan 28, 2011 6:45 am ] |
| Post subject: | Re: Vitara twin transfer kit |
If your going to make the trip we should all go wheeling
|
|
| Author: | RIKSTR [ Sat Jan 29, 2011 1:07 am ] |
| Post subject: | Re: Vitara twin transfer kit |
We made our own slipyoke eliminator, use a flange from a diff, you will find it has the same splines, you will need to weld in a nut or something like that to the flange and get the output shaft tapped and bolt put in but it works great. 
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|