| auszookers.com https://auszookers.com/forum/ |
|
| leaking ball joint https://auszookers.com/forum/viewtopic.php?f=5&t=18755 |
Page 1 of 1 |
| Author: | TryHard [ Tue Feb 01, 2011 12:30 pm ] |
| Post subject: | leaking ball joint |
hey guys today i noticed what i think is a my ball joint leaking basicly im talking about some seal behind hub and its leaked all into my rim what do i replace and how hard is it thanks also is it a ball joint im talking about lol ta |
|
| Author: | alien [ Tue Feb 01, 2011 12:41 pm ] |
| Post subject: | Re: leaking ball joint |
http://www.suzistore.com.au/shopexd.asp?id=1183&bc=no its all a case of undoing bolts, fitting seals, then doing all the bolts back up again, but expect it to take around 1.5hrs per side at least as you need to strip the whole diff down including taking out the wheel bearings and axles. |
|
| Author: | TryHard [ Tue Feb 01, 2011 12:59 pm ] |
| Post subject: | Re: leaking ball joint |
so its my hubs leaking at the back ? so should i do my wheel berings why im at it |
|
| Author: | atari4x4 [ Tue Feb 01, 2011 1:12 pm ] |
| Post subject: | Re: leaking ball joint |
rears are leaking? have a read down the bottom of this thread, there are 2 really good write ups with heaps of pics. http://www.auszookers.com/index.php?name=News&topic=2 |
|
| Author: | dawsey [ Wed Feb 02, 2011 7:02 am ] |
| Post subject: | Re: leaking ball joint |
just put a swivel hub kit through my car ..not to hard a job at all..pretty messy..if you go that far might as well do the wheel bearings ,,not included in the kit ..got the same kit on ebay for $89..Both my hub seals were completly shot.. |
|
| Author: | Teracis [ Wed Feb 02, 2011 7:58 am ] |
| Post subject: | Re: leaking ball joint |
Damn, my right front is leaking, not to the point of dripping on the floor though so I might leave it a while yet. I'm guessing it just leaks the diff oil out? |
|
| Author: | mrw82 [ Wed Feb 02, 2011 7:58 am ] |
| Post subject: | Re: leaking ball joint |
your hub should have grease in it, not oil. I'd say your axle seal is leaking. |
|
| Author: | Teracis [ Wed Feb 02, 2011 8:01 am ] |
| Post subject: | Re: leaking ball joint |
mrw82 wrote: your hub should have grease in it, not oil. I'd say your axle seal is leaking.
I realise the hub should have grease in it, I was just wondering if it sealed the oil in the diff+axle or there was an actual axle seal in the front. It just looks a little wet, I was looking for a grease point but saw no grease nipple on the hub so as you've said I assume it's coming out of the diff 
Unless I'm lucky and it's just melted grease, although it's looking a little too thin for that... |
|
| Author: | TryHard [ Wed Feb 02, 2011 8:39 am ] |
| Post subject: | Re: leaking ball joint |
hey heres some photos of it 
|
|
| Author: | boostedbrick [ Wed Feb 02, 2011 8:55 am ] |
| Post subject: | Re: leaking ball joint |
Teracis wrote: mrw82 wrote: your hub should have grease in it, not oil. I'd say your axle seal is leaking. I realise the hub should have grease in it, I was just wondering if it sealed the oil in the diff+axle or there was an actual axle seal in the front. It just looks a little wet, I was looking for a grease point but saw no grease nipple on the hub so as you've said I assume it's coming out of the diff Unless I'm lucky and it's just melted grease, although it's looking a little too thin for that... The oil will have to get past the grease and scrapers to leak onto the swivel hub.. Check this picture, this is the oil seal that will be leaking, into where the CV sits and the grease is.. |
|
| Author: | Teracis [ Wed Feb 02, 2011 9:30 am ] |
| Post subject: | Re: leaking ball joint |
Damn internet dropped and my last post didn't work. Mine looks to be leaking the same as that one tryhard posted, nowhere near as bad though. Also that seal looks like a bugger to get to! |
|
| Author: | TryHard [ Wed Feb 02, 2011 9:43 am ] |
| Post subject: | Re: leaking ball joint |
so guys anyone know what i need to buy to fix this and what i should change do why im at it ..how hard is this job thank s |
|
| Author: | boostedbrick [ Wed Feb 02, 2011 10:12 am ] |
| Post subject: | Re: leaking ball joint |
http://www.lowrangeoffroad.com/suzuki/s ... -kits.html Thats the kit i brought..Iv have seen them for $80 without wheelbearings on ebay.. but im not sure what quality is like |
|
| Author: | mrw82 [ Thu Feb 03, 2011 5:50 am ] |
| Post subject: | Re: leaking ball joint |
might cost a few $$ but you should replace: axle seal, hub seals, kingpin bearings and wheel bearings. if you want to be a typical suzuki driver and not spend that much money then just replace the axle seal. here's how you do it: 1 remove wheel and freewheeling hub end cap, remove circlip from end of CV shaft 2 remove brake caliper assembly 3 remove brake rotor 4 undo the 4 bolts that are now exposed from removing the rotor, split housing and remove. 5 remove CV from diff housing 6 replace axle seal 7 refit in reverse order. this procedure is a simple task as kingpins, hub wiper seals and wheel bearings do not need to be touched. however if you don't know when they were done last I recommend doing the lot. |
|
| Author: | alien [ Thu Feb 03, 2011 8:28 am ] |
| Post subject: | Re: leaking ball joint |
Tryhard - yours looks like an axle seal - definitely do wheel bearings at the same time - often a collapsed bearing destroys the seal too. |
|
| Author: | TryHard [ Thu Feb 03, 2011 5:40 pm ] |
| Post subject: | Re: leaking ball joint |
hey guys thanks for the advice i think i might just replace the seal and do rest in a few weeks time when i order my front locker and cromolys axle shafts thanks mrw82 for the guide 
it only needs to wheel once at powerlines then its taking a brake lol got a long list of upgrades to do |
|
| Author: | Vash [ Sat Feb 26, 2011 7:05 am ] |
| Post subject: | Re: leaking ball joint |
hey fellas, doing mine now but my question is, you got two bearings at the top & bottom of the housing, with the bearing races. i cant seem to remove the races. do i just slap in replacement bearings? my kit came with replacement races but i cant seem to remove the old ones. cheers. |
|
| Author: | boostedbrick [ Sat Feb 26, 2011 7:09 am ] |
| Post subject: | Re: leaking ball joint |
The way i did it was to use a flat blade, come down thru the race at the top and onto the inside of the race at the bottom. Tap one side, then tap the other one and so on. Than flip over and do the same. There should be a tiny lip that you can get onto on the inside of the race.. |
|
| Author: | Vash [ Sat Feb 26, 2011 7:17 am ] |
| Post subject: | Re: leaking ball joint |
cheers mate. ill give it a shot. also the workshop manual says i gotta cut the swivel seal to fit... but the one i removed wasnt cut?? what the |
|
| Author: | boostedbrick [ Sat Feb 26, 2011 7:55 am ] |
| Post subject: | Re: leaking ball joint |
Its tight but should fit over.. Mine did anyway.. |
|
| Author: | xedent [ Sat Feb 26, 2011 8:11 am ] |
| Post subject: | Re: leaking ball joint |
i am doing this tomorrow, was fun pulling it all apart few months back..... |
|
| Author: | Vash [ Sat Feb 26, 2011 8:20 am ] |
| Post subject: | Re: leaking ball joint |
ok i slipped it over. now im confused after removing the kingpin bearing races, i put the new races in, but now i cant seem to get the new bearings into those races... lol. anyway, very messy indeed... looks like i gotta buy a tub of grease. any brand suggestions? cheers |
|
| Author: | boostedbrick [ Sat Feb 26, 2011 8:25 am ] |
| Post subject: | Re: leaking ball joint |
you put the races in the right way? Knocking em out when there in the wrong way, and not damaging them mite be hard. As for grease, i just use highpressure bearing grease... |
|
| Author: | Vash [ Sat Feb 26, 2011 8:36 am ] |
| Post subject: | Re: leaking ball joint |
the side of the race with the lip faces outwards from the hub right? thats from what i observed as i hammered them out |
|
| Author: | boostedbrick [ Sat Feb 26, 2011 8:49 am ] |
| Post subject: | Re: leaking ball joint |
On the right is what it should look like. 
|
|
| Author: | Vash [ Sat Feb 26, 2011 10:06 pm ] |
| Post subject: | Re: leaking ball joint |
damn i put it in the wrong way... thanks mate. off to the shop to get another two races, i dont think theres any chance of getting the old ones out beside using a dremel. |
|
| Author: | xedent [ Sat Feb 26, 2011 10:38 pm ] |
| Post subject: | Re: leaking ball joint |
I just knocked them out with a center punch ? |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|