auszookers.com
https://auszookers.com/forum/

Changing starter motor in G16B
https://auszookers.com/forum/viewtopic.php?f=5&t=18891		 Page 1 of 1
Author:  ryangus [ Mon Feb 07, 2011 12:08 am ]
Post subject:  Changing starter motor in G16B
Is there a trick to it, cause I can't seem to get near the old one to remove it. Anybody know the steps to changing it?
Author:  Fatzook [ Mon Feb 07, 2011 12:33 am ]
Post subject:  Re: Changing starter motor in G16B
No trick. Its a shitty job, you may need some long reach or ratchet spanners to make it easier, but really you just have to force your hand down there. Its uncomfortable, and you WILL lose skin/ blood. :lol:

I have to change mine on the SV420 today. Solenoid crapped out :roll:
Author:  foolsp33d [ Mon Feb 07, 2011 12:44 am ]
Post subject:  Re: Changing starter motor in G16B
Doing one at the moment to.. Although the inner guard has been trimmed so access is somewhat easier but still a bitch of a job..

Doof will hopefully live this afternoon!
Author:  benqld [ Mon Feb 07, 2011 12:48 am ]
Post subject:  Re: Changing starter motor in G16B
go front underneath, thats what i did.
Author:  steak_knife [ Mon Feb 07, 2011 6:26 am ]
Post subject:  Re: Changing starter motor in G16B
Remove the intake support bracket, than you could get a forklift in there..
3 14mm headed bolt's & a couple of clip's & said bracket's off... :D
Author:  alien [ Mon Feb 07, 2011 7:51 am ]
Post subject:  Re: Changing starter motor in G16B
haha now im dreading mine even more... my starter solenoid was going last winter (got water in it) but its since fixed itself - but thats just been replaced by the starter solenoid going 'click' and not turning the motor... sometimes takes 3-4 goes to get it to kick in =(

i'll wait till its consistently taking a few goes before doing it now... lol
Author:  Fatzook [ Mon Feb 07, 2011 8:39 am ]
Post subject:  Re: Changing starter motor in G16B
alien wrote:
haha now im dreading mine even more... my starter solenoid was going last winter (got water in it) but its since fixed itself - but thats just been replaced by the starter solenoid going 'click' and not turning the motor... sometimes takes 3-4 goes to get it to kick in =(

i'll wait till its consistently taking a few goes before doing it now... lol


Haha thats what mine is doing.... :roll:
Author:  ryangus [ Mon Feb 07, 2011 6:20 pm ]
Post subject:  Re: Changing starter motor in G16B
Fatzook wrote:
alien wrote:
haha now im dreading mine even more... my starter solenoid was going last winter (got water in it) but its since fixed itself - but thats just been replaced by the starter solenoid going 'click' and not turning the motor... sometimes takes 3-4 goes to get it to kick in =(

i'll wait till its consistently taking a few goes before doing it now... lol


Haha thats what mine is doing.... :roll:

and mine. :x

Thanks for the advice everyone.
Author:  alien [ Mon Feb 07, 2011 9:40 pm ]
Post subject:  Re: Changing starter motor in G16B
maybe we didnt respect our starter motors rights at work or something and theyre all going on strike?
Author:  ryangus [ Sat Feb 12, 2011 10:47 pm ]
Post subject:  Re: Changing starter motor in G16B
steak_knife wrote:
Remove the intake support bracket, than you could get a forklift in there..
3 14mm headed bolt's & a couple of clip's & said bracket's off... :D

Well, getting the bracket off was a piece of piss. However, getting to the start motor is still a nightmare. In the end, the starter motor won, and I lost. Walked away cursing to myself.

Anyone keen to do what should be a 20 minute job for a slab?!
Author:  Bucket [ Sat Feb 12, 2011 10:56 pm ]
Post subject:  Re: Changing starter motor in G16B
Bring it down my way and I will. In the past year and a half I've owned my zook, I've had my brushes replaced 3 or 4 times.

Its a bitch of a job, but after doing it so many times, its not a problem :)
Author:  ryangus [ Sun Feb 13, 2011 11:12 am ]
Post subject:  Re: Changing starter motor in G16B
Bucket wrote:
Bring it down my way and I will. In the past year and a half I've owned my zook, I've had my brushes replaced 3 or 4 times.

Its a bitch of a job, but after doing it so many times, its not a problem :)


Thanks mate, but a little too far to drive :lol:
Author:  Fatzook [ Sun Feb 13, 2011 11:25 am ]
Post subject:  Re: Changing starter motor in G16B
Where in Brisbane are you? I could have a look tomorrow ( monday). Give me a call.

0404 057 383

Peter
Author:  shandy92 [ Sun Feb 13, 2011 11:49 am ]
Post subject:  Re: Changing starter motor in G16B
my starter is starting to make a strange noise, it doesnt stop straight away. u can hear it still spinning...for about 2-3 seconds after the motor is running (not engaged on flywheel tho)....does this mean anything?? sorry for the hi-jack.

Mitch
Author:  ryangus [ Mon Feb 14, 2011 7:03 am ]
Post subject:  Re: Changing starter motor in G16B
Fatzook wrote:
Where in Brisbane are you? I could have a look tomorrow ( monday). Give me a call.

0404 057 383

Peter

Sorry mate - but busy today. I'll call you tomorrow.
Author:  alien [ Mon Feb 14, 2011 9:30 am ]
Post subject:  Re: Changing starter motor in G16B
your butt is busy? no exuse for not making a phone call, minus the odd "ee" , "ooh" or "aahhh" =P
Author:  Fatzook [ Mon Feb 14, 2011 9:32 am ]
Post subject:  Re: Changing starter motor in G16B
ryangus wrote:
Fatzook wrote:
Where in Brisbane are you? I could have a look tomorrow ( monday). Give me a call.

0404 057 383

Peter

Sorry mate - but busy today. I'll call you tomorrow.


I'll be at Milton Maccas all day tomorrow fitting a new kitchen. :roll: Wednesday would be 'butt'er for me :lol:
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/