hi all
im putting on my hard top and cant get 3 screws
what is the easy way to get them out
thanks matt
| auszookers.com https://auszookers.com/forum/ |
|
| help cant un do some screws https://auszookers.com/forum/viewtopic.php?f=5&t=19279 |
Page 1 of 1 |
| Author: | Ratty562 [ Sat Feb 19, 2011 9:01 pm ] |
| Post subject: | help cant un do some screws |
hi all im putting on my hard top and cant get 3 screws what is the easy way to get them out
thanks matt |
|
| Author: | want33s [ Sat Feb 19, 2011 9:08 pm ] |
| Post subject: | Re: help cant un do some screws |
HOW TO |
|
| Author: | Hotshot993 [ Sat Feb 19, 2011 9:21 pm ] |
| Post subject: | Re: help cant un do some screws |
Haha as soon as I saw the title I was like someone would have put that tutorial up. |
|
| Author: | squizzytaylor [ Sat Feb 19, 2011 9:38 pm ] |
| Post subject: | Re: help cant un do some screws |
My fav trick of mine depending on the size of the screw is to use a dremel, put 1 slot straight across the screw head and unscrew with a flat head driver. GT |
|
| Author: | monley [ Sat Feb 19, 2011 11:55 pm ] |
| Post subject: | Re: help cant un do some screws |
squizzytaylor wrote: My fav trick of mine depending on the size of the screw is to use a dremel, put 1 slot straight across the screw head and unscrew with a flat head driver.
GT x2 That's never failed me. |
|
| Author: | shakes [ Sun Feb 20, 2011 12:10 am ] |
| Post subject: | Re: help cant un do some screws |
monkey wrote: squizzytaylor wrote: My fav trick of mine depending on the size of the screw is to use a dremel, put 1 slot straight across the screw head and unscrew with a flat head driver. GT x2 That's never failed me. hacksaw blade or grinder for us povo's 
I always seem to snap the screw head off doing it this way |
|
| Author: | shep [ Sun Feb 20, 2011 12:13 am ] |
| Post subject: | Re: help cant un do some screws |
i use a air chisel and wants33s method. |
|
| Author: | Damo [ Sun Feb 20, 2011 12:17 am ] |
| Post subject: | Re: help cant un do some screws |
monkey wrote: squizzytaylor wrote: My fav trick of mine depending on the size of the screw is to use a dremel, put 1 slot straight across the screw head and unscrew with a flat head driver. GT x2 That's never failed me. 3x I use a 1mm cutting disc in an angle grinder and a BFO flat blade screwy. I have one with a square shaft that you can put a shifter on. Works well. |
|
| Author: | bohuler [ Sun Feb 20, 2011 12:57 am ] |
| Post subject: | Re: help cant un do some screws |
Just drill the middle of it out and use an easyout. 
|
|
| Author: | whincup [ Sun Feb 20, 2011 1:13 am ] |
| Post subject: | Re: help cant un do some screws |
recently took off my doors, and want33s method works perfect. either way you need new screws. |
|
| Author: | 303zuke [ Sun Feb 20, 2011 3:30 am ] |
| Post subject: | Re: help cant un do some screws |
You've rooted the head, so just tack weld a nut onto the head and take it out with a socket. |
|
| Author: | Built4thrashing [ Sun Feb 20, 2011 6:58 am ] |
| Post subject: | Re: help cant un do some screws |
Hanner and cold chissel. works everytime. doesnt always leave everything intact but the screw/bolt comes out |
|
| Author: | want33s [ Sun Feb 20, 2011 11:08 am ] |
| Post subject: | Re: help cant un do some screws |
whincup wrote: recently took off my doors, and want33s method works perfect. either way you need new screws.
99% of screws removed by the method I detailed in the link are reusable. No need to butcher them, you only need to crack it then undo with a large phillips. |
|
| Author: | whincup [ Sun Feb 20, 2011 11:21 am ] |
| Post subject: | Re: help cant un do some screws |
want33s wrote: whincup wrote: recently took off my doors, and want33s method works perfect. either way you need new screws. 99% of screws removed by the method I detailed in the link are reusable. No need to butcher them, you only need to crack it then undo with a large phillips. mine needed a little bit of convincing to turn...  maybe i was just unlucky, or too impatient.
|
|
| Author: | monley [ Sun Feb 20, 2011 11:25 am ] |
| Post subject: | Re: help cant un do some screws |
I had a screw i had get out on Friday> It was a screw going though 2 real thin peaces of sheet metal, the head of the screw was fine but the thread was stuff just behind the head of the screw and it was just spinning, so got a old screw driver hit the head of the screw to bend it then it gripped and i got it out.
|
|
| Author: | salih [ Mon Feb 21, 2011 3:58 am ] |
| Post subject: | Re: help cant un do some screws |
mate i had the same trouble for the same job. use a impact screwdriver gets em out straight away |
|
| Author: | stiky [ Mon Feb 21, 2011 5:05 am ] |
| Post subject: | Re: help cant un do some screws |
Heat the screw |
|
| Author: | steak_knife [ Mon Feb 21, 2011 7:12 am ] |
| Post subject: | Re: help cant un do some screws |
salih wrote: mate i had the same trouble for the same job.
use a impact screwdriver gets em out straight away Not all way's, I've busted impact bit's & had to resort to the chisel trick..... Even had to drill.. |
|
| Author: | Ratty562 [ Mon Feb 21, 2011 8:34 am ] |
| Post subject: | Re: help cant un do some screws |
thanks all the chisel trick worked well how i just gotta move my roll bar because the roof was sitting in the bar matt |
|
| Author: | salih [ Mon Feb 21, 2011 8:49 am ] |
| Post subject: | Re: help cant un do some screws |
steak_knife wrote: salih wrote: mate i had the same trouble for the same job. use a impact screwdriver gets em out straight away Not all way's, I've busted impact bit's & had to resort to the chisel trick..... Even had to drill.. well it worked for me on like 3 diffrent screws maybe just lucky 
i have to admit on one of my old sierras it dident work so i grinded it off lol |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|