use this and a breaker bar, or a rattle gun
| auszookers.com https://auszookers.com/forum/ |
|
| I'm taking apart a transfer case, please help! https://auszookers.com/forum/viewtopic.php?f=5&t=19497 |
Page 1 of 1 |
| Author: | shane1992 [ Sat Feb 26, 2011 3:00 am ] |
| Post subject: | I'm taking apart a transfer case, please help! |
Hey, So im installing gears in my transfercase, how do I undo the bolts on the driveshaft flanges? The instructions say they are 28mm.. Does one of the flanges need to be held with some kind of vice? Cause it just spins around and I cant find anything to help stop that... Thanks guys |
|
| Author: | 31zook [ Sat Feb 26, 2011 3:05 am ] |
| Post subject: | Re: I'm taking apart a transfer case, please help! |
|
use this and a breaker bar, or a rattle gun
|
|
| Author: | 94BAZOOKA [ Sat Feb 26, 2011 3:06 am ] |
| Post subject: | Re: I'm taking apart a transfer case, please help! |
I believe there is a flange removal tool it's just a bar with two studs that u slip in the bolt hole while you undo the center nut or you could just try get it in the vice |
|
| Author: | 94BAZOOKA [ Sat Feb 26, 2011 3:07 am ] |
| Post subject: | Re: I'm taking apart a transfer case, please help! |
Haha beat me to it 31zook |
|
| Author: | BlueSuzy [ Sat Feb 26, 2011 3:07 am ] |
| Post subject: | Re: I'm taking apart a transfer case, please help! |
Strong Rattle gun and socket or Vice Spanner + hammer Possibly Heat to loosen it up. |
|
| Author: | 31zook [ Sat Feb 26, 2011 3:15 am ] |
| Post subject: | Re: I'm taking apart a transfer case, please help! |
94BAZOOKA wrote: flange removal tool
thats exactly what i googled 
|
|
| Author: | shane1992 [ Sat Feb 26, 2011 3:16 am ] |
| Post subject: | Re: I'm taking apart a transfer case, please help! |
Cheers everyone!! More tools added to the shopping list!! |
|
| Author: | pyrohamish [ Sat Feb 26, 2011 5:01 am ] |
| Post subject: | Re: I'm taking apart a transfer case, please help! |
flange in the vice, socket to suit, rattle gun and try and pry out the indents in the nut that are there to stop it spinning. |
|
| Author: | shep [ Sat Feb 26, 2011 5:12 am ] |
| Post subject: | Re: I'm taking apart a transfer case, please help! |
i just put on a welding glove and held on tightly while upping it with a rattle gun. |
|
| Author: | shane1992 [ Sat Feb 26, 2011 5:21 am ] |
| Post subject: | Re: I'm taking apart a transfer case, please help! |
I dont got air tools, I gotta make my face turn blue on these kinda situations... Also with installing the 6.5's, will this make my speedo as accurate as it was when stock? |
|
| Author: | shep [ Sat Feb 26, 2011 5:37 am ] |
| Post subject: | Re: I'm taking apart a transfer case, please help! |
it wont make a difference to your speedo mate |
|
| Author: | buzbox [ Sat Feb 26, 2011 5:40 am ] |
| Post subject: | Re: I'm taking apart a transfer case, please help! |
shane1992 wrote: I dont got air tools.
You can bring it over mine, I've got a decent bench vice but my garage is a shit tip at the moment or I'll bring my compressor and gun over to yours.
It shouldn't take long. |
|
| Author: | neofitou [ Sat Feb 26, 2011 7:01 am ] |
| Post subject: | Re: I'm taking apart a transfer case, please help! |
Two bolt hols and bolts in a peice of RHS or angle = custom flange tool. works a treat. Clamp it to your bench or stand on it, slip another peice of steel on your socket and your laughing. I had one that the rattle gun wouldnt do, but the bf breaker bar did, great big crack when it went. And Im pretty sure they are 27mm not 28. Just tap out the indents with a slim center punch first. |
|
| Author: | shane1992 [ Sat Feb 26, 2011 8:24 am ] |
| Post subject: | Re: I'm taking apart a transfer case, please help! |
Been trying all arvo, Broke some shit in the process too. Yeah Dave I think I am going to have to take you up on that offer!! Whatevers easier for you |
|
| Author: | birko [ Sat Feb 26, 2011 9:02 am ] |
| Post subject: | Re: I'm taking apart a transfer case, please help! |
a peice of flat bar with two bolt in at the right spacing is just and good and cheaper |
|
| Author: | shane1992 [ Sat Feb 26, 2011 9:28 am ] |
| Post subject: | Re: I'm taking apart a transfer case, please help! |
birko wrote: a peice of flat bar with two bolt in at the right spacing is just and good and cheaper
Yeah had my mate stading on tansfer case with 2 bolts in and crow bar wedges in, It just bent my drive shaft bolts ay lol, Needs a rattle gun I think. Very stubbrn |
|
| Author: | skyman [ Sat Feb 26, 2011 3:44 pm ] |
| Post subject: | Re: I'm taking apart a transfer case, please help! |
Quote: pry out the indents in the nut that are there to stop it spinning.
/\ This /\ is good advice. Just don't use a cheap pikc or screwdriver to pry out the indent, it will break off, and pinned the nut on there even harder. I learned the hard way, and had a broken off tip of a screwdriver in there holding it solid. 
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|