A big flat head screw driver is often enough to place against the nut and lever back onto something to jam it to hold it.
Take a couple photo's for us, might help
| auszookers.com https://auszookers.com/forum/ |
|
| Spinning bolt !!! https://auszookers.com/forum/viewtopic.php?f=5&t=19516 |
Page 1 of 1 |
| Author: | Zooknoob [ Sun Feb 27, 2011 12:35 am ] |
| Post subject: | Spinning bolt !!! |
Hey I'm trying to take my front bar off but but the 4 bolts that are holding the bracket on are just spinning and there's no room to get anything inside to hold the other side in to stop spinning an 1 have and ideas on how the get them off or how to snap them off |
|
| Author: | Benz [ Sun Feb 27, 2011 12:42 am ] |
| Post subject: | Re: Spinning bolt !!! |
angel grinder? |
|
| Author: | Zooknoob [ Sun Feb 27, 2011 12:48 am ] |
| Post subject: | Re: Spinning bolt !!! |
Yer I was thinking that but to no room to get it in under the chase |
|
| Author: | shakes [ Sun Feb 27, 2011 2:06 am ] |
| Post subject: | Re: Spinning bolt !!! |
A big flat head screw driver is often enough to place against the nut and lever back onto something to jam it to hold it. Take a couple photo's for us, might help
|
|
| Author: | Teracis [ Sun Feb 27, 2011 2:43 am ] |
| Post subject: | Re: Spinning bolt !!! |
Or a hacksaw blade (or reciprocating saw/sabre saw if you have one) to cut them off. |
|
| Author: | steak_knife [ Sun Feb 27, 2011 7:23 am ] |
| Post subject: | Re: Spinning bolt !!! |
shakes wrote: A big flat head screw driver is often enough to place against the nut and lever back onto something to jam it to hold it.
Take a couple photo's for us, might help 
or hammer & cold chisel... 
|
|
| Author: | bazook [ Sun Feb 27, 2011 7:52 am ] |
| Post subject: | Re: Spinning bolt !!! |
or oxy, or if you can get vice grips on it you could just wiggle it up and down |
|
| Author: | Taylor74 [ Mon Feb 28, 2011 8:24 am ] |
| Post subject: | Re: Spinning bolt !!! |
I do love my plasma cutter
|
|
| Author: | Scrawny [ Mon Feb 28, 2011 8:45 am ] |
| Post subject: | Re: Spinning bolt !!! |
steak_knife wrote: shakes wrote: A big flat head screw driver is often enough to place against the nut and lever back onto something to jam it to hold it. Take a couple photo's for us, might help or hammer & cold chisel... Yeah, big hammer, big sharp chisel. Just don't hit ya hand
|
|
| Author: | steak_knife [ Mon Feb 28, 2011 9:08 am ] |
| Post subject: | Re: Spinning bolt !!! |
ScrawnC wrote: steak_knife wrote: shakes wrote: A big flat head screw driver is often enough to place against the nut and lever back onto something to jam it to hold it. Take a couple photo's for us, might help or hammer & cold chisel... Yeah, big hammer, big sharp chisel. Just don't hit ya hand That's what I'm doing wrong.... 
|
|
| Author: | Scrawny [ Mon Feb 28, 2011 9:10 am ] |
| Post subject: | Re: Spinning bolt !!! |
steak_knife wrote: ScrawnC wrote: steak_knife wrote: shakes wrote: A big flat head screw driver is often enough to place against the nut and lever back onto something to jam it to hold it. Take a couple photo's for us, might help or hammer & cold chisel... Yeah, big hammer, big sharp chisel. Just don't hit ya hand That's what I'm doing wrong.... I use a cast iron fry pan, seem to have better success |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|