| auszookers.com https://auszookers.com/forum/ |
|
| is this engine suitable for rebuild? https://auszookers.com/forum/viewtopic.php?f=5&t=19807 |
Page 1 of 1 |
| Author: | experament-u2 [ Mon Mar 07, 2011 10:56 am ] |
| Post subject: | is this engine suitable for rebuild? |
hi all, my sierras current engine is getting very long in the tooth, and im looking to replaced it. i am looking to keep the 1.3 after no luck finding a suitable motor i scored a unknown condition motor for a carton of piss. i just removed the head and found a bit of water in the 2nd and 3rd cilinder (from being out in weather) so my question is this block to far gone? thanks 
|
|
| Author: | ball [ Mon Mar 07, 2011 11:10 am ] |
| Post subject: | Re: is this engine suitable for rebuild? |
What is the bore size ? |
|
| Author: | sideways [ Mon Mar 07, 2011 11:26 am ] |
| Post subject: | Re: is this engine suitable for rebuild? |
Looks good to me, especially if it's standard bore. |
|
| Author: | experament-u2 [ Mon Mar 07, 2011 11:38 am ] |
| Post subject: | Re: is this engine suitable for rebuild? |
pretty sure its stock bore size |
|
| Author: | matfan [ Mon Mar 07, 2011 12:06 pm ] |
| Post subject: | Re: is this engine suitable for rebuild? |
you're a can of wd40 away from a shmick looking block! |
|
| Author: | fordem [ Mon Mar 07, 2011 5:56 pm ] |
| Post subject: | Re: is this engine suitable for rebuild? |
Clean it up - if necessary bore +0.02 OS. |
|
| Author: | zooky08 [ Mon Mar 07, 2011 9:20 pm ] |
| Post subject: | Re: is this engine suitable for rebuild? |
Looks alright to me If it's standard bore size, just clean the block up nd get it bored to 20 thou over and get new pistons to match |
|
| Author: | experament-u2 [ Tue Mar 08, 2011 3:04 am ] |
| Post subject: | Re: is this engine suitable for rebuild? |
i can see a little bit of pitting on one or two of the cylinders, would this mean it is best to clean it up (degrease it like crazy) myself then take it to someone that can give it a final proper clean and bore it out a little? and should i be getting the head re skimmed? also were is the best place to buy a rebuild kit for the g13? this is (obviously) my first engine rebuild 
|
|
| Author: | zooky08 [ Tue Mar 08, 2011 3:34 am ] |
| Post subject: | Re: is this engine suitable for rebuild? |
Clean it up as much as you can Get it bored out to 20 thou Get you head and block shaved I got all my parts from t-Mac Not sure what you have around your area |
|
| Author: | experament-u2 [ Tue Mar 08, 2011 6:45 am ] |
| Post subject: | Re: is this engine suitable for rebuild? |
for the rebuild kit i was looking at a master rebuld kit from lowrange has being the best price iv seen so far http://www.lowrangeoffroad.com/suzuki/s ... parts.html |
|
| Author: | steak_knife [ Tue Mar 08, 2011 6:51 am ] |
| Post subject: | Re: is this engine suitable for rebuild? |
http://www.acl.com.au/  buy aus made, I've been using ACL for yr's... 
|
|
| Author: | zooky08 [ Tue Mar 08, 2011 8:14 am ] |
| Post subject: | Re: is this engine suitable for rebuild? |
i wouldnt buy standard size pistons either |
|
| Author: | TZAR [ Tue Mar 08, 2011 8:48 am ] |
| Post subject: | Re: is this engine suitable for rebuild? |
put it back to gether and slap it in. She will be right |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|