auszookers.com
https://auszookers.com/forum/

removing axels
https://auszookers.com/forum/viewtopic.php?f=5&t=19839		 Page 1 of 1
Author:  zooky08 [ Tue Mar 08, 2011 10:51 pm ]
Post subject:  removing axels
i cant seem to get my rear axels out to replace my bairings
ive tried every thing in this post,

http://www.auszookers.com/index.php?nam ... ving+axels

still wont come out
im just destroying what ever i hit, which i dont really want
does any one else have any ideas
Author:  JrZook [ Tue Mar 08, 2011 10:54 pm ]
Post subject:  Re: removing axels
Have you tried a length of chain? Bolt it tight onto one of the axle studs and repeatedly 'whip' the chain. That should crack it loose!
Author:  atari4x4 [ Tue Mar 08, 2011 10:59 pm ]
Post subject:  Re: removing axels
http://www.auszookers.com/index.php?nam ... ic&t=19477
Author:  zooky08 [ Tue Mar 08, 2011 11:29 pm ]
Post subject:  Re: removing axels
havnt tried the chain idea, but i do have the hub bolted on backwards.
a sledge hammer didnt even do it, doubt a chain will, but i will try the chain idea.

btw diff isnt bolted to the car
Author:  zooky08 [ Wed Mar 09, 2011 12:21 am ]
Post subject:  Re: removing axels
chain didnt work, so thought i should give it a couple more hits with the hammer and it came out

now time to get the beairings off :? :cry:
Author:  whincup [ Wed Mar 09, 2011 12:36 am ]
Post subject:  Re: removing axels
they have to be cut off, AFAIK. thats how mine were done, and how my service manual tells me to get them off.
Author:  zooky08 [ Wed Mar 09, 2011 12:55 am ]
Post subject:  Re: removing axels
whincup wrote:
they have to be cut off, AFAIK. thats how mine were done, and how my service manual tells me to get them off.


aww god dam it

thanks
Author:  tanshi [ Wed Mar 09, 2011 1:02 am ]
Post subject:  Re: removing axels
you can some times press them off, but its far easier to use a grinder and just grind through the retaining ring, then you can usually get the bearing off resonably easy
Author:  atari4x4 [ Wed Mar 09, 2011 1:10 am ]
Post subject:  Re: removing axels
there is this tech article written by foolsp33d

http://www.auszookers.com/index.php?nam ... cle&sid=17
Author:  zooky08 [ Wed Mar 09, 2011 1:43 am ]
Post subject:  Re: removing axels
Great article, thanks guys
Author:  Westie [ Wed Mar 09, 2011 2:19 am ]
Post subject:  Re: removing axels
JrZook wrote:
Have you tried a length of chain? Bolt it tight onto one of the axle studs and repeatedly 'whip' the chain. That should crack it loose!

Chain work well if used with a length of pipe through it and a hand on the top and the bottom and use that to snap it back onto the chain as this acts like an slide hammer and will give it that impact affect.
Author:  zooky08 [ Wed Mar 09, 2011 2:36 am ]
Post subject:  Re: removing axels
I did try a solid steel bar with the chain wrapped around it, also a hammer
Didn't work so I gave up nd smacked it a bit more nd they came out
Author:  31zook [ Wed Mar 09, 2011 2:48 am ]
Post subject:  Re: removing axels
zooky08 wrote:
I did try a solid steel bar with the chain wrapped around it, also a hammer
Didn't work so I gave up nd smacked it a bit more nd they came out


i was trying to get my axle out of the housing like that and i pulled it off of the car jacks :lol:


Now days i undo the four bolts, undo the brake line, pull it out and up, plug it (also using a pair of pliers with ziptie on the rubber brake line). Then because mine is a NT i don't have a hand brake to worry about, i just put on my spare rim and give it 2 solid hit's and it's out, no damage to anything :D and i just grind very very carefully to get the bearing off.....
Author:  zooky08 [ Wed Mar 09, 2011 3:19 am ]
Post subject:  Re: removing axels
Thanks 31zook

Lucky I don't need these diff just yet, cos I've wrecked a few bits including the brake line :cry:
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/