| auszookers.com https://auszookers.com/forum/ |
|
| Spring locating pins/holes don't line up https://auszookers.com/forum/viewtopic.php?f=5&t=19922 |
Page 1 of 1 |
| Author: | SierraDan [ Fri Mar 11, 2011 9:56 pm ] |
| Post subject: | Spring locating pins/holes don't line up |
Suzuki Sierra, 2" Lovells spring lift. The hole on the spring perch is about 10mm back from the pin on the spring. The shackle is also all the way to the stop. How the f#%^ do I get them to line up? |
|
| Author: | BlueSuzy [ Fri Mar 11, 2011 10:03 pm ] |
| Post subject: | Re: Spring locating pins/holes don't line up |
what? I read that 5 times.. A pic mite explain it better |
|
| Author: | appsie [ Fri Mar 11, 2011 10:08 pm ] |
| Post subject: | Re: Spring locating pins/holes don't line up |
the rear end im guessing?? are they definately rears? |
|
| Author: | SierraDan [ Fri Mar 11, 2011 10:13 pm ] |
| Post subject: | Re: Spring locating pins/holes don't line up |
yeah driver rear at the moment. they are definitely rears. and it has "D/S" on it so i know its the right one. just isnt being cooperative... uploading pictures now. |
|
| Author: | SierraDan [ Fri Mar 11, 2011 10:16 pm ] |
| Post subject: | Re: Spring locating pins/holes don't line up |
|
|
|
| Author: | 89_tintop [ Fri Mar 11, 2011 10:31 pm ] |
| Post subject: | Re: Spring locating pins/holes don't line up |
unbolt it from the shackle... allign diff into pin then jack that side of the diff up and put the shackle back through.. |
|
| Author: | bazook [ Fri Mar 11, 2011 10:44 pm ] |
| Post subject: | Re: Spring locating pins/holes don't line up |
have you un done the passenger side u bolts |
|
| Author: | SierraDan [ Fri Mar 11, 2011 10:47 pm ] |
| Post subject: | Re: Spring locating pins/holes don't line up |
How do I then get the shackle back on? I haven't no. Doing one corner at a time. |
|
| Author: | SierraDan [ Fri Mar 11, 2011 10:52 pm ] |
| Post subject: | Re: Spring locating pins/holes don't line up |
Just undid the shackle. Same situation. Just no it's no attached at the shackle end. |
|
| Author: | SuziBlu [ Fri Mar 11, 2011 11:04 pm ] |
| Post subject: | Re: Spring locating pins/holes don't line up |
Move the diff. I put or tried to put in camber wedges, wrong size holes, when I went to set it back as it was, same problem your having. Undo both spring hangers, move the diff to align the holes, then do the hangers, you may have to use force to get the hangers back on, I did, no biggy really. When doing one side only, everything is held in position by the other side, undoing both sides makes it a piece of cake. |
|
| Author: | Teracis [ Fri Mar 11, 2011 11:09 pm ] |
| Post subject: | Re: Spring locating pins/holes don't line up |
SuziBlu wrote: Move the diff. I put or tried to put in camber wedges, wrong size holes, when I went to set it back as it was, same problem your having.
Undo both spring hangers, move the diff to align the holes, then do the hangers, you may have to use force to get the hangers back on, I did, no biggy really. When doing one side only, everything is held in position by the other side, undoing both sides makes it a piece of cake. I haven't done it but mine has the diff moved back, make sure you check clearances for your shocks e.t.c once you've moved it. |
|
| Author: | TZAR [ Fri Mar 11, 2011 11:15 pm ] |
| Post subject: | Re: Spring locating pins/holes don't line up |
Put jack stands under chassis and let the diff droop. Undo everything and then bolt in springs. THEN do up U bolts loosly and align diff. Then fully clamp down and hold diff down. You can't expect lifted springs to be exactly the same as standard springs can you. This is a good learning curve for you. Helps understand the way springs work. If you undo the u bolts on both sides it will be so easy you will beat your self for not doing it earlier |
|
| Author: | want33s [ Fri Mar 11, 2011 11:20 pm ] |
| Post subject: | Re: Spring locating pins/holes don't line up |
I've changed heaps of springs one at a time..(My car has quite an appetite for them) Jack up the spring until the diff is supported by it and then kick the diff into place. Sounds rough but works and saves a lot of time.... In your case if you are changing both rear springs loosen the Ubolts on the other side and you should be able to align the locating pin fairly easily. |
|
| Author: | Ratty562 [ Fri Mar 11, 2011 11:29 pm ] |
| Post subject: | Re: Spring locating pins/holes don't line up |
x2 jack the the springs up. i only just did mine in the rear and it worked for my first time on changing the springs. matt |
|
| Author: | SierraDan [ Fri Mar 11, 2011 11:46 pm ] |
| Post subject: | Re: Spring locating pins/holes don't line up |
I undid the p/s ubolts moved the diff. Cheers guys. Now my shackle won't go in. Will the angle return when the springs get some weight on it and settle in? |
|
| Author: | BlueSuzy [ Fri Mar 11, 2011 11:59 pm ] |
| Post subject: | Re: Spring locating pins/holes don't line up |
Ah so you only undid half of it.... Yes the shackle will return..Depending on how stiff the springs are. |
|
| Author: | SierraDan [ Sat Mar 12, 2011 1:51 am ] |
| Post subject: | Re: Spring locating pins/holes don't line up |
Thanks guys. It's all going well now 
Rear is up! Having a break then doing the front WITH AIR TOOLS! (I'm buggered) |
|
| Author: | royce [ Sat Mar 12, 2011 3:04 am ] |
| Post subject: | Re: Spring locating pins/holes don't line up |
my quick way of doing 2 springs jack up, stands under chassis, let suspension drop undo all ubolts, lift diff clear slightly and hold with more stands undo and remove shackle, let spring drop, same for other side remove pin other end, chuck old spring and slip new one in and do up loosley, same for other side lift up spring and put shackle back in, do up loosly drop diff onto springs, slide into locating holes and put plates and u bolts in lower back to ground and do pins and shackles up never need any effort to get anything to line up that way |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|