Have a look in HERE. Pretty sure he did the conversion
| auszookers.com https://auszookers.com/forum/ |
|
| how hard is it to put a g13b into a coily sierra?? https://auszookers.com/forum/viewtopic.php?f=5&t=20702 |
Page 1 of 1 |
| Author: | sambo91 [ Tue Apr 05, 2011 8:23 am ] |
| Post subject: | how hard is it to put a g13b into a coily sierra?? |
hey there zookers. after missing out on a complete one already converted. i am wondering how hard is it to put a g13b into my coily?? and how much power difference there is. any help or previous experience will be appretiated =) |
|
| Author: | Rusho [ Tue Apr 05, 2011 8:31 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
Have a look in HERE. Pretty sure he did the conversion
|
|
| Author: | Teracis [ Tue Apr 05, 2011 10:46 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
Assuming you mean g13bb? The injected version out of a jimny? Your old man should be able to help you wire it up so really it should be a no brainer, afaik the engine is literally bolt in it's just the wiring that is the "hard" part. If you mean the g16b (1.6 injected) then it's more work. Why do you want more power yet anyway? did you blow up your engine? |
|
| Author: | royce [ Tue Apr 05, 2011 10:50 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
no he means G13B GTI engine |
|
| Author: | Teracis [ Tue Apr 05, 2011 10:54 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
royce wrote: no he means G13B GTI engine
Ah, well sorry about that, gti conversion is a fair bit more involved though right? |
|
| Author: | Fatzook [ Tue Apr 05, 2011 12:08 pm ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
something..... |
|
| Author: | royce [ Tue Apr 05, 2011 8:52 pm ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
Teracis wrote: royce wrote: no he means G13B GTI engine Ah, well sorry about that, gti conversion is a fair bit more involved though right? Dont worry, I used to always call the G13ba an G13b, Jonno had to whinge at me about it for quite some time before I changed 
|
|
| Author: | SierraDan [ Tue Apr 05, 2011 9:13 pm ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
I'm interested in this also. Wiring I'm comfortable with. Fabrication I'm a bit messy haha. |
|
| Author: | sambo91 [ Tue Apr 05, 2011 10:41 pm ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
yeah i was talking about the g13b out of the gti. but the g13bb wouldnt be to bad either. Wiring im sweet with too. its the engine mounts and stuff that gets me. |
|
| Author: | Fatzook [ Tue Apr 05, 2011 10:44 pm ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
sambo91 wrote: yeah i was talking about the g13b out of the gti. but the g13bb wouldnt be to bad either. Wiring im sweet with too. its the engine mounts and stuff that gets me.
AFAIK all of the G13 variants have the same block. So they should al just bolt straight into a sierra on standard sierra mounts. 
|
|
| Author: | SierraDan [ Wed Apr 06, 2011 1:45 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
Fatzook wrote: sambo91 wrote: yeah i was talking about the g13b out of the gti. but the g13bb wouldnt be to bad either. Wiring im sweet with too. its the engine mounts and stuff that gets me. AFAIK all of the G13 variants have the same block. So they should al just bolt straight into a sierra on standard sierra mounts. Keeeeen! |
|
| Author: | sambo91 [ Thu Apr 07, 2011 3:27 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
i second that. how much does a g13bb and b cost. and whats the better option? |
|
| Author: | Teracis [ Thu Apr 07, 2011 6:03 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
I was thinking about doing a g13bb, until more than one person told me they like to crack heads 
If someone could confirm this to be untrue or at least explain why they do it so it could be avoided, it would put this conversion back on the table as efi would be boss! |
|
| Author: | Fatzook [ Thu Apr 07, 2011 7:39 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
I sold a G13BB to Saam a few years back. He droped it into his coily and its still kicking along nicely.
|
|
| Author: | Teracis [ Thu Apr 07, 2011 7:41 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
Fatzook wrote: I sold a G13BB to Saam a few years back. He droped it into his coily and its still kicking along nicely.
Stop making me want to do a conversion! Read: Please help me justify it!
|
|
| Author: | Fatzook [ Thu Apr 07, 2011 7:45 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
Teracis wrote: Fatzook wrote: I sold a G13BB to Saam a few years back. He droped it into his coily and its still kicking along nicely. Stop making me want to do a conversion! Read: Please help me justify it! Whats stopping you? Do you have the budget for the conversion? Have you considered the alternatives? Do you keep your balls in your missus handbag? 
|
|
| Author: | Teracis [ Thu Apr 07, 2011 7:56 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
Fatzook wrote: Teracis wrote: Fatzook wrote: I sold a G13BB to Saam a few years back. He droped it into his coily and its still kicking along nicely. Stop making me want to do a conversion! Read: Please help me justify it! Whats stopping you? Do you have the budget for the conversion? Have you considered the alternatives? Do you keep your balls in your missus handbag? Don't NEED to do it yet, budget is too thin at the moment and I don't know what a G13BB is worth yet, It's gonna cost about 2/3 as much to rebuild the engine and carby (working on $1500 for a G13BB with loom and ecu) so it looks like a good option, but then it's an untested motor again... Alternatives being 1.6 which costs more and is more work? Also, balls aren't in the handbag, but if I want to keep and not have them cut off I am not going to spend heaps on the zook when I'm already spending 10k on my half of a new engine for the ski boat... |
|
| Author: | sambo91 [ Thu Apr 07, 2011 11:16 pm ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
confirmation from dad is that wiring looms for him are a piece of piss. so could be looking at doing a conversion somewhere down the track =P do you have to do the 90 degree dizzy relocation with the bb?? |
|
| Author: | JrZook [ Fri Apr 08, 2011 1:02 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
sambo91 wrote: confirmation from dad is that wiring looms for him are a piece of piss. so could be looking at doing a conversion somewhere down the track =P
do you have to do the 90 degree dizzy relocation with the bb?? Nope! The BB runs twin coils and a cam sensor, so no dizzy to worry about |
|
| Author: | JrZook [ Fri Apr 08, 2011 1:03 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
Teracis wrote: I'm already spending 10k on my half of a new engine for the ski boat...
Why would you only wanna spend on half an engine? 
|
|
| Author: | Teracis [ Fri Apr 08, 2011 1:08 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
JrZook wrote: Teracis wrote: I'm already spending 10k on my half of a new engine for the ski boat... Why would you only wanna spend on half an engine? Coz dad is spending the other 10k on his half :p going for either a 150 or 175 optimax to put on our 19ft millennium hull (which used to have an 80-90 model bitsa 225 johnson) Dad was told by the bloke at the shop that we don't NEED the 175 unless we plan on pulling 4 skiers at a time... Not sure what the price difference is but they are the same engine with different injectors and ecu e.t.c. so will decide based on price. Meanwhile back in zook territory, what's a g13bb worth? as it sounds by far to be the easiest efi conversion (bar throttle body...) |
|
| Author: | FHA57 [ Fri Apr 08, 2011 3:30 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
better off with a low k g13bb as its very hard to find a decent g13b without lots of k's saams g13bb went well but spend a bit more not much more i might add and do the 1.6 g13bb doesnt make a huge difference over the 1.3 carby i mean its noticeable but nothing compared to a good 1.6 |
|
| Author: | Teracis [ Fri Apr 08, 2011 3:36 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
FHA57 wrote: better off with a low k g13bb as its very hard to find a decent g13b without lots of k's saams g13bb went well but spend a bit more not much more i might add and do the 1.6 g13bb doesnt make a huge difference over the 1.3 carby i mean its noticeable but nothing compared to a good 1.6
How much are we talking? G13bb only need engine and loom + ecu right? G16b? (injected one) need engine, adapter plate, loom + ecu, exhaust manifold/extractors + Mod plate yeh? I did a bunch of research a while back for 4age conversion, then decided the work + cost would be more than I had in a budget. |
|
| Author: | JrZook [ Fri Apr 08, 2011 3:43 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
Teracis wrote: FHA57 wrote: better off with a low k g13bb as its very hard to find a decent g13b without lots of k's saams g13bb went well but spend a bit more not much more i might add and do the 1.6 g13bb doesnt make a huge difference over the 1.3 carby i mean its noticeable but nothing compared to a good 1.6 How much are we talking? G13bb only need engine and loom + ecu right? G16b? (injected one) need engine, adapter plate, loom + ecu, exhaust manifold/extractors + Mod plate yeh? I did a bunch of research a while back for 4age conversion, then decided the work + cost would be more than I had in a budget. Correct me if I'm wrong but since your also modding the fuel system (carby to EFI) don't you need a mod plate for the overall engine conversion still in QLD? If this is the case then the only major difference between 1600 and 1300 injected swaps in the adapter plate. |
|
| Author: | SierraDan [ Fri Apr 08, 2011 4:14 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
Is the g13bb out of the early jimnys? |
|
| Author: | JrZook [ Fri Apr 08, 2011 4:20 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
SierraDan wrote: Is the g13bb out of the early jimnys?
Yes |
|
| Author: | Teracis [ Fri Apr 08, 2011 8:01 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
JrZook wrote: Teracis wrote: FHA57 wrote: better off with a low k g13bb as its very hard to find a decent g13b without lots of k's saams g13bb went well but spend a bit more not much more i might add and do the 1.6 g13bb doesnt make a huge difference over the 1.3 carby i mean its noticeable but nothing compared to a good 1.6 How much are we talking? G13bb only need engine and loom + ecu right? G16b? (injected one) need engine, adapter plate, loom + ecu, exhaust manifold/extractors + Mod plate yeh? I did a bunch of research a while back for 4age conversion, then decided the work + cost would be more than I had in a budget. Correct me if I'm wrong but since your also modding the fuel system (carby to EFI) don't you need a mod plate for the overall engine conversion still in QLD? If this is the case then the only major difference between 1600 and 1300 injected swaps in the adapter plate. What about the exhaust, I didn't think the 1300 extractors would fit the 1600? |
|
| Author: | JrZook [ Fri Apr 08, 2011 8:03 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
Teracis wrote: JrZook wrote: Teracis wrote: FHA57 wrote: better off with a low k g13bb as its very hard to find a decent g13b without lots of k's saams g13bb went well but spend a bit more not much more i might add and do the 1.6 g13bb doesnt make a huge difference over the 1.3 carby i mean its noticeable but nothing compared to a good 1.6 How much are we talking? G13bb only need engine and loom + ecu right? G16b? (injected one) need engine, adapter plate, loom + ecu, exhaust manifold/extractors + Mod plate yeh? I did a bunch of research a while back for 4age conversion, then decided the work + cost would be more than I had in a budget. Correct me if I'm wrong but since your also modding the fuel system (carby to EFI) don't you need a mod plate for the overall engine conversion still in QLD? If this is the case then the only major difference between 1600 and 1300 injected swaps in the adapter plate. What about the exhaust, I didn't think the 1300 extractors would fit the 1600? G13BB head is the same as teh 1600 16V head. The g13a/ba's wont fit either. |
|
| Author: | Teracis [ Fri Apr 08, 2011 8:05 am ] |
| Post subject: | Re: how hard is it to put a g13b into a coily sierra?? |
JrZook wrote: Teracis wrote: JrZook wrote: Teracis wrote: FHA57 wrote: better off with a low k g13bb as its very hard to find a decent g13b without lots of k's saams g13bb went well but spend a bit more not much more i might add and do the 1.6 g13bb doesnt make a huge difference over the 1.3 carby i mean its noticeable but nothing compared to a good 1.6 How much are we talking? G13bb only need engine and loom + ecu right? G16b? (injected one) need engine, adapter plate, loom + ecu, exhaust manifold/extractors + Mod plate yeh? I did a bunch of research a while back for 4age conversion, then decided the work + cost would be more than I had in a budget. Correct me if I'm wrong but since your also modding the fuel system (carby to EFI) don't you need a mod plate for the overall engine conversion still in QLD? If this is the case then the only major difference between 1600 and 1300 injected swaps in the adapter plate. What about the exhaust, I didn't think the 1300 extractors would fit the 1600? G13BB head is the same as teh 1600 16V head. The g13a/ba's wont fit either. Ah bugger, I was thinking it would be piss easy to swap over. Oh well, add exhaust to it and the only extra cost becomes the extra for the engine and the $200 for the adapter plate. Now, what's a 1.6 efi worth? |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|