hi all
was just wondering if anyone had modified a snakeraceing Transfer Cradle to fit into a sj40 ute as they have a different mounting points
thanks
| auszookers.com https://auszookers.com/forum/ |
|
| Transfer Cradle https://auszookers.com/forum/viewtopic.php?f=5&t=21360 |
Page 1 of 1 |
| Author: | Ratty562 [ Tue Apr 26, 2011 10:00 am ] |
| Post subject: | Transfer Cradle |
hi all was just wondering if anyone had modified a snakeraceing Transfer Cradle to fit into a sj40 ute as they have a different mounting points
thanks |
|
| Author: | alien [ Tue Apr 26, 2011 10:02 am ] |
| Post subject: | Re: Transfer Cradle |
lol whats with the giant booger hanging out of the plug? haha |
|
| Author: | Ratty562 [ Tue Apr 26, 2011 10:06 am ] |
| Post subject: | Re: Transfer Cradle |
thats oil from the case. lol didnt even see that till now. |
|
| Author: | BlueSuzy [ Wed Apr 27, 2011 2:14 am ] |
| Post subject: | Re: Transfer Cradle |
Its only the 1 mount that is not right..right? Id move the flat mount on the chassis so it lines up with the transfer bracket. Is that crossmember original?? |
|
| Author: | steak_knife [ Wed Apr 27, 2011 6:45 am ] |
| Post subject: | Re: Transfer Cradle |
BlueSuzy wrote: Its only the 1 mount that is not right..right?
Id move the flat mount on the chassis so it lines up with the transfer bracket. Is that crossmember original?? for a Lt, yep... |
|
| Author: | Rusho [ Wed Apr 27, 2011 7:30 am ] |
| Post subject: | Re: Transfer Cradle |
Looks like a shit load of work mate....maybe you should sell it to me instead 
|
|
| Author: | Ratty562 [ Wed Apr 27, 2011 9:01 am ] |
| Post subject: | Re: Transfer Cradle |
yeh it all original. thats kinda hard for me as im not that good a welding thin stuff |
|
| Author: | BlueSuzy [ Wed Apr 27, 2011 9:19 am ] |
| Post subject: | Re: Transfer Cradle |
where abouts are you? I could help. |
|
| Author: | steak_knife [ Wed Apr 27, 2011 9:19 am ] |
| Post subject: | Re: Transfer Cradle |
Move the front mount on the case cradle back to where it's needed & chop off the excess.... |
|
| Author: | Gwagensteve [ Wed Apr 27, 2011 9:29 am ] |
| Post subject: | Re: Transfer Cradle |
Can't see why this job requires welding? Drill a new hole in the snake crossmember to line up with the 1.0 mount location, and use the 1.0 mount with the two factory 1.0 bushes on the tension side - looks pretty easy to me. I think the 1.0 litre mount arrangement is superior to the 1.3 setup. no rubber mounts to break and four mounts not three. Steve. |
|
| Author: | steak_knife [ Wed Apr 27, 2011 9:48 am ] |
| Post subject: | Re: Transfer Cradle |
 that's what I said Mr Gman..... 
|
|
| Author: | Ratty562 [ Wed Apr 27, 2011 11:16 am ] |
| Post subject: | Re: Transfer Cradle |
that sounds like it will work ill give it a go thanks all |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|