auszookers.com :: View topic - diff breather's help 16/6/08

once you undo the factory diff breather i assume that it will unscrew from that welded nutsert???

what size is the hole/thread so that i can put some festo quick fit elbows in help asap cheers at work for anoth 1hour need to know so i can buy some from work.cheers nick

the hose supplied should fit straight over that and then clamp it up.

But what I done on mine was get a 1/8bsp tap, ran it down that hole (perfect fit, no drilling required) and then screwed a brass hosetail fitting into it and used a smaller hose. (half inch hose is major overkill)

just make sure to change the diff oil after doing this and give it a blow through to remove any filings.

Author:	zook89 [ Fri May 23, 2008 10:00 pm ]
Post subject:	diff breather's help 16/6/08
i brought a piranha kit and the guy told me just to pop the factory cap off and the new air line will go straight on but thats not the case i pop it off and there's a hole nothin to put the line on to whats next help cheers nick

Author:	steve [ Fri May 23, 2008 10:08 pm ]
Post subject:	Re: diff breather's help
doesn't the hose fit over the diff breather nozel thingy? did you tell him it was a sierra? I guess ya did?

Author:	mrw82 [ Fri May 23, 2008 10:52 pm ]
Post subject:	Re: diff breather's help
the hose supplied should fit straight over that and then clamp it up. But what I done on mine was get a 1/8bsp tap, ran it down that hole (perfect fit, no drilling required) and then screwed a brass hosetail fitting into it and used a smaller hose. (half inch hose is major overkill) just make sure to change the diff oil after doing this and give it a blow through to remove any filings.

Author:	lilzook [ Fri May 23, 2008 11:49 pm ]
Post subject:	Re: diff breather's help
i used about 100mm of 1/2 fuel line 1/2 male barb 1/4 bsp to 1/4 female barb 1/4 bsb. (2x front/back) 4m 1/4" fuel line. 8x Clamps to suit. 2x inline fuel filters. rpf1005 cost under $40

Author:	zook89 [ Mon Jun 16, 2008 9:06 pm ]
Post subject:	Re: diff breather's help
once you undo the factory diff breather i assume that it will unscrew from that welded nutsert??? what size is the hole/thread so that i can put some festo quick fit elbows in help asap cheers at work for anoth 1hour need to know so i can buy some from work.cheers nick

auszookers.com https://auszookers.com/forum/

diff breather's help 16/6/08 https://auszookers.com/forum/viewtopic.php?f=5&t=2157	Page 1 of 1

Author:	Damo [ Mon Jun 16, 2008 9:10 pm ]
Post subject:	Re: diff breather's help
zook89 wrote: once you undo the factory diff breather i assume that it will unscrew from that welded nutsert??? The cap is just crimped on, you can pry it off with a screwdriver. Underneath that cap should be a spring which holds a little disk down over the nipple welded into the diff housing. zook89 wrote: what size is the hole/thread so that i can put some festo quick fit elbows in help asap cheers at work for anoth 1hour need to know so i can buy some from work.cheers nick mrw82 wrote: the hose supplied should fit straight over that and then clamp it up. But what I done on mine was get a 1/8bsp tap, ran it down that hole (perfect fit, no drilling required) and then screwed a brass hosetail fitting into it and used a smaller hose. (half inch hose is major overkill) just make sure to change the diff oil after doing this and give it a blow through to remove any filings.

Author:	zook89 [ Mon Jun 16, 2008 9:15 pm ]
Post subject:	Re: diff breather's help 16/6/08
so that factory fitting shown in the picturte does not un screw???

Author:	Damo [ Mon Jun 16, 2008 9:37 pm ]
Post subject:	Re: diff breather's help 16/6/08
zook89 wrote: so that factory fitting shown in the picturte does not un screw??? No, it's welded into the housing.

Author:	zook89 [ Mon Jun 16, 2008 9:48 pm ]
Post subject:	Re: diff breather's help 16/6/08
damm ok no probs thanks for your help.

Page 1 of 1	All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/