auszookers.com
https://auszookers.com/forum/

BALENO G16B Info
https://auszookers.com/forum/viewtopic.php?f=5&t=21809		 Page 1 of 1
Author:  MG410 [ Mon May 09, 2011 11:36 pm ]
Post subject:  BALENO G16B Info
I just bought a G16B from a damaged Baleno, what extra parts from Car are required for the transplant to Sierra/Maruti,also does anyone Make or have a design for the Water outlet at rear of Motor.
Thanks
Author:  BlueSuzy [ Tue May 10, 2011 12:00 am ]
Post subject:  Re: BALENO G16B Info
Read here:
http://www.auszookers.com/index.php?nam ... 23&start=0

And here, because your engine mounts will be suited for a 1L(going by your username)
http://www.auszookers.com/index.php?nam ... 99&start=0

And here:
http://www.outerlimits4x4.com/viewtopic ... lit=Baleno
Author:  MG410 [ Tue May 10, 2011 12:41 am ]
Post subject:  Re: BALENO G16B Info
I already have G13ba fitted with 1.3 mounts and a Bent adapter,just got to remove all required parts from Baleno wreck this weekend.
Author:  BlueSuzy [ Tue May 10, 2011 12:55 am ]
Post subject:  Re: BALENO G16B Info
MG410 wrote:
I already have G13ba fitted with 1.3 mounts and a Bent adapter,just got to remove all required parts from Baleno wreck this weekend.


Really just need the motor and all wiring(including the cluster if you want a stockish tacho if coilpack model)

Twin coil or dizzy?
Author:  xedent [ Tue May 10, 2011 1:00 am ]
Post subject:  Re: BALENO G16B Info
If you already have 1.3 mounts it's pretty strait forward, just need motor, loom, cluster.

You will need a thermostat housing from an early swift, it's right angle.

You will need the 1.3 sump and pickup, you have to cut the piece from the bal sump where crank sensor is and weld to your sierra sump.

Should also get vl commodore rb30 engine mounts as these are way stronger.

Probably more but that's all I can think of the top of my head.

Good luck.
Author:  BlueSuzy [ Tue May 10, 2011 1:03 am ]
Post subject:  Re: BALENO G16B Info
xedent wrote:
If you already have 1.3 mounts it's pretty strait forward, just need motor, loom, cluster.

You will need a thermostat housing from an early swift, it's right angle.

You will need the 1.3 sump and pickup, you have to cut the piece from the bal sump where crank sensor is and weld to your sierra sump.

Should also get vl commodore rb30 engine mounts as these are way stronger.

Probably more but that's all I can think of the top of my head.

Good luck.


check the links.. :lol:
Author:  matty87 [ Tue May 10, 2011 1:07 am ]
Post subject:  Re: BALENO G16B Info
Take everything that dosent take up much room. Then ditch the body. You will be surprised at the usefulness of the parts.
Author:  MG410 [ Tue May 10, 2011 1:28 am ]
Post subject:  Re: BALENO G16B Info
Thanks all
Its the coil pack version [No Dizzy] and its up the Central Coast NSW,just making sure I dont leave anything behind that might be required.Been reading the 16B post just double checking.
Author:  dp87 [ Tue May 10, 2011 2:27 am ]
Post subject:  Re: BALENO G16B Info
http://i161.photobucket.com/albums/t218 ... omrear.jpg


is that what u need made up?

im after one too
Author:  BlueSuzy [ Tue May 10, 2011 2:48 am ]
Post subject:  Re: BALENO G16B Info
Some people are able to use the stocko one with a swift housing on it.

I wasnt able to as my engine was closer to the firewall, and good luck changing the thermostat..

There is many threads on this already.

I have to make one again for my new one.

Should i make 3.. :lol:
Author:  dp87 [ Tue May 10, 2011 5:47 am ]
Post subject:  Re: BALENO G16B Info
hey mate if you could get one made up for me that would be awesome. when are you thinking about doing it?

i havnt fitted my engine yet, im waiting to get my sump welded by fatzook. everything else is ready to go.

im pretty sure that i need something like that made up because i have 2inch bodylift and im using VL engine mounts
Author:  MG410 [ Tue May 10, 2011 9:33 am ]
Post subject:  Re: BALENO G16B Info
If you got time to make extra fitting I am interested,PM price
The motor I picking up is from 2000 Baleno manual
Author:  Birdman1985 [ Wed May 11, 2011 3:47 am ]
Post subject:  Re: BALENO G16B Info
Thanks alot!!!!!!!!

I was bidding on that! Pipped me on the last second.
Author:  94BAZOOKA [ Wed May 11, 2011 6:17 am ]
Post subject:  Re: BALENO G16B Info
MG410 wrote:
If you got time to make extra fitting I am interested,PM price
The motor I picking up is from 2000 Baleno manual



I'll pick the motor up from lake munmorah and install it for you

In my car :lol:
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/