auszookers.com
https://auszookers.com/forum/

removing gearbox in a serria
https://auszookers.com/forum/viewtopic.php?f=5&t=22134		 Page 1 of 1
Author:  Ratty562 [ Sat May 21, 2011 2:44 am ]
Post subject:  removing gearbox in a serria
hi all

im talking my gearbox out to change my clutch but it does not want to come out. ive un-done all the bolts. was just wondering do i have to take the starter moter out to remove the gearbox

thanks
Author:  swifty_ano [ Sat May 21, 2011 2:47 am ]
Post subject:  Re: removing gearbox in a serria
Yes you do.
It may need so persuasion too
Author:  reeceh [ Sat May 21, 2011 3:51 am ]
Post subject:  Re: removing gearbox in a serria
Take the starter out. Remember to drop all your gearbox mounts. Then get a big fuckoff blade screwdriver and wedge it between the bellhousing and back of block and u will have to wriggle it about. Just make sure u have at least 2 people with you for safety sake. You gave to wriggle it off the pins!
Author:  Ratty562 [ Sat May 21, 2011 5:23 am ]
Post subject:  Re: removing gearbox in a serria
thanks all.
got it all out now. dont think ill do that again lol

thanks
Author:  liamhh [ Sat May 21, 2011 10:47 am ]
Post subject:  Re: removing gearbox in a serria
Did you end up having to unbolt and move the engine forward to clear the input shaft when dropping the box? Because I did and it was a bit of a prick to do solo.
Author:  Ratty562 [ Sat May 21, 2011 1:02 pm ]
Post subject:  Re: removing gearbox in a serria
No didn't move the engine. I just unbolted the front drive shaft and the input shaft and I just came out pretty easy when everything was out of the way
Author:  steve125 [ Sat May 21, 2011 10:48 pm ]
Post subject:  Re: removing gearbox in a serria
Ratty562 wrote:
thanks all.
got it all out now. dont think ill do that again lol

thanks


Now the fun bit, getting it back in.

Took me three or four goes of trying to get the flat top of the bell housing past the clutch before I realised you need to rotate the gearbox about 45 degrees for it to clear.
Author:  zooky08 [ Sat May 21, 2011 11:07 pm ]
Post subject:  Re: removing gearbox in a serria
Ratty562 wrote:
I just unbolted the front drive shaft
this doesnt need to come out.
Also do what steve125 said
Much easier when you tilt the box on a angle
You will see what way to go when you get to it
Author:  boostedbrick [ Sat May 21, 2011 11:55 pm ]
Post subject:  Re: removing gearbox in a serria
zooky08 wrote:
Ratty562 wrote:
I just unbolted the front drive shaft
this doesnt need to come out.
Also do what steve125 said
Much easier when you tilt the box on a angle
You will see what way to go when you get to it



It has to come out on mine due to exhuast location, i think it would be the the case with other people aswell... Whats four bolts to make a job eaiser..
Author:  zooky08 [ Sun May 22, 2011 12:03 am ]
Post subject:  Re: removing gearbox in a serria
My exhaust must be in a different location then others then :?
I don't recall taking no drive shaft off just the crossmember
Author:  boostedbrick [ Sun May 22, 2011 12:47 am ]
Post subject:  Re: removing gearbox in a serria
Let me reword that, some other people. My cat is right off the end of the headers and hits. It came out easy for Ratty562 anyway so it worked.
Author:  Ratty562 [ Sun May 22, 2011 1:45 am ]
Post subject:  Re: removing gearbox in a serria
yeh my cat is right under the gearbox so i just droped one end of the drive shaft to make it easy for the box to drop out
Author:  zooky08 [ Sun May 22, 2011 2:31 am ]
Post subject:  Re: removing gearbox in a serria
boostedbrick wrote:
Let me reword that, some other people. My cat is right off the end of the headers and hits. It came out easy for Ratty562 anyway so it worked.
Yes I know what you ment
Mines just different to others that's all
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/