Ben_Sierra wrote:
Hit it.
If that doesn't work, hit it harder!
If that doesn't work, hit it harder!
Don't use force, use a bigger hammer.
| auszookers.com https://auszookers.com/forum/ |
|
| Counter Shaft in transfer case https://auszookers.com/forum/viewtopic.php?f=5&t=22288 |
Page 1 of 1 |
| Author: | stockman [ Thu May 26, 2011 2:13 am ] |
| Post subject: | Counter Shaft in transfer case |
I pulled my case apart the other day, but the countershaft was stuck. I removed the locking tab on the outside of the case but the shaft won't budge. Any trick on getting it out? |
|
| Author: | JrZook [ Thu May 26, 2011 2:26 am ] |
| Post subject: | Re: Counter Shaft in transfer case |
WD40 and tap with hammer? |
|
| Author: | Ben_Sierra [ Thu May 26, 2011 2:29 am ] |
| Post subject: | Re: Counter Shaft in transfer case |
Hit it. If that doesn't work, hit it harder! |
|
| Author: | SuziBlu [ Thu May 26, 2011 2:37 am ] |
| Post subject: | Re: Counter Shaft in transfer case |
Ben_Sierra wrote: Hit it.
If that doesn't work, hit it harder! Don't use force, use a bigger hammer.
|
|
| Author: | JrZook [ Thu May 26, 2011 2:38 am ] |
| Post subject: | Re: Counter Shaft in transfer case |
SuziBlu wrote: Ben_Sierra wrote: Hit it. If that doesn't work, hit it harder! Don't use force, use a bigger hammer. F=m*a how can you not use force? 
|
|
| Author: | stockman [ Thu May 26, 2011 2:59 am ] |
| Post subject: | Re: Counter Shaft in transfer case |
I only tried the strong arm. I will try hammer next! |
|
| Author: | Ben_Sierra [ Thu May 26, 2011 3:00 am ] |
| Post subject: | Re: Counter Shaft in transfer case |
JrZook wrote: SuziBlu wrote: Ben_Sierra wrote: Hit it. If that doesn't work, hit it harder! Don't use force, use a bigger hammer. F=m*a how can you not use force? Bigger hammer, less acceleration, same force
|
|
| Author: | SuziBlu [ Thu May 26, 2011 3:27 am ] |
| Post subject: | Re: Counter Shaft in transfer case |
lol was meant as a silly, but instead of smacking the shit out of it with a light hammer, let inertia do the job, use a bigger hammer, swung with good force, much more inertia. Always use a brass drift, never steel on steel. |
|
| Author: | steak_knife [ Thu May 26, 2011 7:15 am ] |
| Post subject: | Re: Counter Shaft in transfer case |
Has an O'ring on the end, could have corosion in there to, so wd or similar & a lil love tap should see you clear... 
|
|
| Author: | PJ.zook [ Thu May 26, 2011 8:33 am ] |
| Post subject: | Re: Counter Shaft in transfer case |
I find that swearing at it and graphically describing sexual acts I would do to its mother helps things along. |
|
| Author: | Built4thrashing [ Thu May 26, 2011 9:17 am ] |
| Post subject: | Re: Counter Shaft in transfer case |
threaten it with a 9 inch.  .. grinder
|
|
| Author: | zukenutter [ Mon Jun 13, 2011 3:47 am ] |
| Post subject: | Re: Counter Shaft in transfer case |
Why does the counter shaft protrude through the case, thus needing an 'O' ring? Is there a maintenance reason for this? |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|