You don't need any of these for manual transmissions, they have a sealed and supported output.
still give the cash if you like though
| auszookers.com https://auszookers.com/forum/ |
|
| vitara 5spd to sierra transfercase https://auszookers.com/forum/viewtopic.php?f=5&t=22927 |
Page 1 of 1 |
| Author: | evolution [ Thu Jun 16, 2011 11:10 pm ] |
| Post subject: | vitara 5spd to sierra transfercase |
Ok building a buggy for Tuff Truck dropping the 1.6 into a 92 sierra and want to run the stronger vitara 5spd. Dose anyone make an adaptor to remove the vitara transfercase and just run the divorced sierra one Duncan |
|
| Author: | =wardy= [ Fri Jun 17, 2011 1:41 am ] |
| Post subject: | Re: vitara 5spd to sierra transfercase |
give locked up a call thay sell a kit so you can run you standard jack sharft from a vitara auto so i,m gessing they would do something for the 5spd Wardy |
|
| Author: | atari4x4 [ Fri Jun 17, 2011 1:47 am ] |
| Post subject: | Re: vitara 5spd to sierra transfercase |
check out JML Gear in the business directory, joeblow has a similar set up to whats available from locktup for the auto, not sure how much work it would be to adapt to a manual. http://www.auszookers.com/index.php?nam ... ic&t=20147 |
|
| Author: | joeblow [ Fri Jun 17, 2011 3:11 am ] |
| Post subject: | Re: vitara 5spd to sierra transfercase |
You don't need any of these for manual transmissions, they have a sealed and supported output. still give the cash if you like though
|
|
| Author: | evolution [ Fri Jun 17, 2011 10:26 am ] |
| Post subject: | Re: vitara 5spd to sierra transfercase |
So if I drop the vitara transfercase of then the jack shaft is the same size and spline count as the out put of the vitara 5spd that would be cool. |
|
| Author: | Fatzook [ Fri Jun 17, 2011 10:40 am ] |
| Post subject: | Re: vitara 5spd to sierra transfercase |
This is the back of the 5sp. Just drop the transfer off and shove the jack shaft up its arse 
|
|
| Author: | shandy92 [ Fri Jun 17, 2011 11:54 am ] |
| Post subject: | Re: vitara 5spd to sierra transfercase |
yeah should bolt straight up, maybe new mounts for the box and some tunnel work. |
|
| Author: | evolution [ Sat Jun 18, 2011 12:23 am ] |
| Post subject: | Re: vitara 5spd to sierra transfercase |
Is there a seal already in the out put of the vit 5spd were the jack shaft will go in and whats the large bottom hole for. |
|
| Author: | shandy92 [ Sat Jun 18, 2011 2:35 am ] |
| Post subject: | Re: vitara 5spd to sierra transfercase |
evolution wrote: Is there a seal already in the out put of the vit 5spd were the jack shaft will go in and whats the large bottom hole for. joeblow wrote: You don't need any of these for manual transmissions, they have a sealed and supported output.
i guess this answers your question, im not sure about the lower hole. im sure someone will. |
|
| Author: | Fatzook [ Sat Jun 18, 2011 2:40 am ] |
| Post subject: | Re: vitara 5spd to sierra transfercase |
In the pic I posted, that hole supports a shaft from the transfercase. I have left the front of the transfer on there so that I can run the seal (sits around the splined shaft and slip yoke of a jackshaft) The hole at the bottom just needs to have a welch plug tapped in to seal it
|
|
| Author: | evolution [ Sat Jun 18, 2011 5:25 am ] |
| Post subject: | Re: vitara 5spd to sierra transfercase |
Thank you so much will be going this way then stronger box and bigger clutch. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|