auszookers.com
https://auszookers.com/forum/

1.3 box to 1.6 box
https://auszookers.com/forum/viewtopic.php?f=5&t=22931		 Page 1 of 1
Author:  boostedbrick [ Fri Jun 17, 2011 12:49 am ]
Post subject:  1.3 box to 1.6 box
My current 1.3 5 speed is pretty well shagged. So I figure if im going for a replacement I may as well fit a vitara box well the body is off to make it easier. My G16B already had the 1.3 box fitted when i purchased it.
Will i still be able to run the current clutch and flywheel?
Looking at the benT kit, it comes with replacement mounting studs. Im guessing these will have tobe replaced with standard units?
And are tunnel mods needed with a 2 inch body lift?
Author:  steak_knife [ Fri Jun 17, 2011 6:35 am ]
Post subject:  Re: 1.3 box to 1.6 box
boostedbrick wrote:
My current 1.3 5 speed is pretty well shagged. So I figure if im going for a replacement I may as well fit a vitara box well the body is off to make it easier. My G16B already had the 1.3 box fitted when i purchased it.
Will i still be able to run the current clutch and flywheel?
Looking at the benT kit, it comes with replacement mounting studs. Im guessing these will have tobe replaced with standard units?
And are tunnel mods needed with a 2 inch body lift?


No, starter won't engage the flying wheel.

Why do you need a BenT kit to fit a vit box to a vit eng???? :?
Author:  boostedbrick [ Fri Jun 17, 2011 6:49 am ]
Post subject:  Re: 1.3 box to 1.6 box
It has a Ben t kit on it... meaning the vit box probally won't bolt on with the bent studs.
Author:  Fatzook [ Fri Jun 17, 2011 7:25 am ]
Post subject:  Re: 1.3 box to 1.6 box
boostedbrick wrote:
It has a Ben t kit on it... meaning the vit box probally won't bolt on with the bent studs.


No it won't. Thats what bolt shops are for :wink:

You may still need a bit of tunnel mods with the vit box. Even with the BL fitted......
Author:  boostedbrick [ Fri Jun 17, 2011 8:37 am ]
Post subject:  Re: 1.3 box to 1.6 box
Fatzook wrote:
boostedbrick wrote:
It has a Ben t kit on it... meaning the vit box probally won't bolt on with the bent studs.


No it won't. Thats what bolt shops are for :wink:

You may still need a bit of tunnel mods with the vit box. Even with the BL fitted......


Ah yer figured that was the case..
Don't mind doing minor tunnel mods, as long as i don't have to reshape the whole thing. Now to see if i can find a flywheel that isnt bolted to an engine :|
Author:  Fatzook [ Fri Jun 17, 2011 8:40 am ]
Post subject:  Re: 1.3 box to 1.6 box
Shouldn't be too hard. There are plenty of dead G16's out there :wink:
Author:  steak_knife [ Fri Jun 17, 2011 9:15 am ]
Post subject:  Re: 1.3 box to 1.6 box
boostedbrick wrote:
Now to see if i can find a flywheel that isnt bolted to an engine :|


I think I have one......
Author:  boostedbrick [ Fri Jun 17, 2011 9:40 am ]
Post subject:  Re: 1.3 box to 1.6 box
Cool :)
Author:  steak_knife [ Fri Jun 17, 2011 9:54 am ]
Post subject:  Re: 1.3 box to 1.6 box
boostedbrick wrote:
Cool :)


:P Should be, it's in the shed & it's frucking cold in there..... :P
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/