auszookers.com
https://auszookers.com/forum/

G13BB into Baleno
https://auszookers.com/forum/viewtopic.php?f=5&t=22995		 Page 1 of 1
Author:  watermouse [ Sun Jun 19, 2011 1:16 am ]
Post subject:  G13BB into Baleno
I have just bought an immaculate condition 2001 Baleno ( coilpack 1.6) that's only done 90000km. $4200!! :D

OK, so it's going to be used as our second car in the immediate future but I am already eyeing off the engine to replace the aging donk in the Jimny.

So if or when i get around to swapping out the 1.6 for the Jimny I was wondering if anyone would have any ideas about putting the 1.3 back into the Baleno at least to keep it moving. That is, in the true essence of a swap

Do-able? Reverse a BenT adapter plate? Swift gearbox?

:crazy:
Author:  want33s [ Sun Jun 19, 2011 1:34 am ]
Post subject:  Re: G13BB into Baleno
Just buy another Baleno from the auctions for a few hundred dollars.
Pull the G16B out fit your G13BB head and wack it in the Jim.
Author:  Teracis [ Sun Jun 19, 2011 1:41 am ]
Post subject:  Re: G13BB into Baleno
want33s wrote:
Just buy another Baleno from the auctions for a few hundred dollars.
Pull the G16B out fit your G13BB head and wack it in the Jim.


I've been looking for one of these "few hundred dollar baleno's" and buggered if I can find the right auctions

Any links?
Author:  boostedbrick [ Sun Jun 19, 2011 2:20 am ]
Post subject:  Re: G13BB into Baleno
Teracis wrote:
want33s wrote:
Just buy another Baleno from the auctions for a few hundred dollars.
Pull the G16B out fit your G13BB head and wack it in the Jim.


I've been looking for one of these "few hundred dollar baleno's" and buggered if I can find the right auctions

Any links?


Pickles and manheim have baleno's quite often...

http://www.pickles.com.au/damaged/listi ... N&x=43&y=8
Author:  Teracis [ Sun Jun 19, 2011 4:05 am ]
Post subject:  Re: G13BB into Baleno
Been looking at pickles, the only ones they have are on the other side of the country, I'll keep my eye out though!

EDIT: Other end, victoria is a tad far from here to just pop down and get one!
Author:  runtbase [ Sun Jun 19, 2011 6:01 am ]
Post subject:  Re: G13BB into Baleno
What is the benefit of fitting the g13bb head to the g16b
Author:  xedent [ Sun Jun 19, 2011 7:15 am ]
Post subject:  Re: G13BB into Baleno
Same head, you don't have water outlet etc out the back
Author:  want33s [ Sun Jun 19, 2011 7:15 am ]
Post subject:  Re: G13BB into Baleno
runtbase wrote:
What is the benefit of fitting the g13bb head to the g16b

Then you have water outlet at front. No messing around with water pipes from the firewall to radiator.
Author:  Gwagensteve [ Sun Jun 19, 2011 7:34 am ]
Post subject:  Re: G13BB into Baleno
That's nothing to do with the head though - it's the inlet manifold and a blanking plate on the back of the head.

Steve.
Author:  stockman [ Sun Jun 19, 2011 7:37 am ]
Post subject:  Re: G13BB into Baleno
Isn't the outlet on the manifold.
Would it be possible to swap the manifold and blank the head?

Steve beat me to it. :)
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/