Scrawn wrote:
It takes me 20mins on a hoist to get a box out of a Sierra, you just have to hold your tongue right
how did u get the gearbox down past the pressure plate without them touching.
| auszookers.com https://auszookers.com/forum/ |
|
| is it easier to take the engine out to change a clutch? https://auszookers.com/forum/viewtopic.php?f=5&t=22997 |
Page 1 of 1 |
| Author: | Sutho [ Sun Jun 19, 2011 2:12 am ] |
| Post subject: | is it easier to take the engine out to change a clutch? |
is it easier to take the engine out to change a clutch in a sierra? 1.3l |
|
| Author: | boostedbrick [ Sun Jun 19, 2011 2:16 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
Takes 45 to pull a box.. 90 to pull a carby engine... Box is defiantly the way to go. |
|
| Author: | smiffkid [ Sun Jun 19, 2011 2:41 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
depends who is doing it, if your a wizz at pulling the engine out then thats prob the quickest way, or if u got the room to pull the box out do it that way, i know for me its alot quicker to pull the box out, |
|
| Author: | sogone [ Sun Jun 19, 2011 2:45 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
Box wins. |
|
| Author: | stockman [ Sun Jun 19, 2011 3:00 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
If you don't have the luxury of a hoist and you don't want to mess around crawling under a car pull the engine out too. When the motor is out it will be much easier to do the rear main. Whilst it's out perfect opertunity to do anything else that needs doing. |
|
| Author: | Sutho [ Sun Jun 19, 2011 3:50 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
a gear box does not come out without fouling something, we just spent 3.5 hours trying to get the box out. i dont have the luxury of body lift so that doesnt help IMO its quicker and easier to pull the engine and gearbox out in 1 unit, i have the luxury of a hoist and a workshop my dad was a mechanic for 30 years and he cant believe that it has taken 3.5 hours to try and get it out, theres no way u can do it without fouling the pressure plate on the bell housing, we removed everything to make it easier and jacked the engine up and pulled it forward. |
|
| Author: | Scrawny [ Sun Jun 19, 2011 4:22 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
It takes me 20mins on a hoist to get a box out of a Sierra, you just have to hold your tongue right |
|
| Author: | Sutho [ Sun Jun 19, 2011 4:27 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
Scrawn wrote: It takes me 20mins on a hoist to get a box out of a Sierra, you just have to hold your tongue right
how did u get the gearbox down past the pressure plate without them touching.
|
|
| Author: | ajsr [ Sun Jun 19, 2011 5:03 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
Scrawn wrote: It takes me 20mins on a hoist to get a box out of a Sierra, you just have to hold your tongue right
about 30 min on the ground with a rattle gun take the box monunt off |
|
| Author: | jimbo_jones [ Sun Jun 19, 2011 5:23 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
Sutho wrote: Scrawn wrote: It takes me 20mins on a hoist to get a box out of a Sierra, you just have to hold your tongue right how did u get the gearbox down past the pressure plate without them touching.Im with scrawn easy as pull the box |
|
| Author: | JrZook [ Sun Jun 19, 2011 5:26 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
Sutho wrote: a gear box does not come out without fouling something, we just spent 3.5 hours trying to get the box out.
i dont have the luxury of body lift so that doesnt help IMO its quicker and easier to pull the engine and gearbox out in 1 unit, i have the luxury of a hoist and a workshop my dad was a mechanic for 30 years and he cant believe that it has taken 3.5 hours to try and get it out, theres no way u can do it without fouling the pressure plate on the bell housing, we removed everything to make it easier and jacked the engine up and pulled it forward. WTF 3.5hrs with experience that's uber long!! All I ever do is loosen the engine mounts, take the dizzy out and support the sump with a stand/jack. This lowers the rear of the engine making it easier to get the box in/out. Watch your fan/shroud clearance also when you do this. Dan |
|
| Author: | Scrawny [ Sun Jun 19, 2011 5:54 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
Sutho wrote: Scrawn wrote: It takes me 20mins on a hoist to get a box out of a Sierra, you just have to hold your tongue right how did u get the gearbox down past the pressure plate without them touching.Been a while since I've done one but I think I rolled the box on it's side then pushed the motor up. I didn't touch any engine mounts |
|
| Author: | boostedbrick [ Sun Jun 19, 2011 5:59 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
Scrawn wrote: Sutho wrote: Scrawn wrote: It takes me 20mins on a hoist to get a box out of a Sierra, you just have to hold your tongue right how did u get the gearbox down past the pressure plate without them touching.Been a while since I've done one but I think I rolled the box on it's side then pushed the motor up. I didn't touch any engine mounts I roll it on it side at it comes out with out undoing the engine mounts. Remove the front driveshaft as my cat is in the way, and completely remove the reart mount from the car.. |
|
| Author: | steve125 [ Sun Jun 19, 2011 6:00 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
Sutho wrote: how did u get the gearbox down past the pressure plate without them touching.
Was it getting caught on the flat top of gearbox bell housing? If you rotate the gearbox about 45 degrees so that the rounded sides of the bell housing are at the top it should clear OK. |
|
| Author: | sogone [ Sun Jun 19, 2011 6:14 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
I'm with boostedbrick. Front drive shaft out. Gearbox mount removed and bit of a twist of the box and your tongue out the right way and it falls out. |
|
| Author: | honks [ Sun Jun 19, 2011 6:28 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
i had a similar problem but i got it out easy just could not get it back in so un done the left engine mount twisted the engine enough to get the box sitting up in the tunnel then twisted it back to bolt the box back up. |
|
| Author: | Junior_91 [ Sun Jun 19, 2011 10:28 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
Did both mine and my sisters on the ground at home and it was all done in about 2 hours from drive in to drive out. Not that hard at all just gotta twist it bit and bam out it comes onto your arm which was sposed to catch it 
|
|
| Author: | zookcubr [ Sun Jun 19, 2011 10:42 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
On a Vit I think id rather take the motor out, the manual boxs are bloody heavy. |
|
| Author: | royce [ Sun Jun 19, 2011 10:47 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
zookcubr wrote: On a Vit I think id rather take the motor out, the manual boxs are bloody heavy.
soft  I can lift one in and out
|
|
| Author: | zookcubr [ Sun Jun 19, 2011 10:52 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
Not with the transfer case attached lying on your back under the car |
|
| Author: | TryHard [ Sun Jun 19, 2011 12:59 pm ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
here's a Tip and it makes it alot easyer for later on what u will find when u go to drop your box out is it will foul up on the cross member what u need to do to its get a angle grinder and trim the cross member i think its about 30 mill to secs il get a photo up
|
|
| Author: | TryHard [ Sun Jun 19, 2011 1:06 pm ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
here u can see iv trimmed it 
what u need 2 do is trim that then u can move the box back enuf so it wont foul up on the pressure plate i had the same issue mate
btw this is a photo of the rear gearbox / mount cross member this way u dont need to twist or anything just pull back and drop down vista virsa
|
|
| Author: | nadsdrawkcab [ Sun Jun 19, 2011 9:12 pm ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
I did mine several time on the driveway with jackstands. Found it was easier to slide the gearbox back away from the engine and rest the front of the box on a jackstand, then kinda squeeze in between them and remove the clutch assy. More room to manouver the box out. Especially with a couple of inches of suspension lift giving more room to move. Just watch when undoing the clutch assy, alloy bellhousings bite. |
|
| Author: | skyman [ Mon Jun 20, 2011 2:42 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
TryHard wrote: here's a Tip and it makes it alot easyer for later on what u will find when u go to drop your box out is it will foul up on the cross member what u need to do to its get a angle grinder and trim the cross member i think its about 30 mill
to secs il get a photo up Best advice for puling a gear box out of a sierra ...Ever! armsup armsup It is a very common mod over here. |
|
| Author: | TryHard [ Mon Jun 20, 2011 3:06 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
Ya It makes it So much Easyer
|
|
| Author: | SierraDan [ Mon Jun 20, 2011 4:14 am ] |
| Post subject: | Re: is it easier to take the engine out to change a clutch? |
It doesn't weaken it at all? |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|