auszookers.com
https://auszookers.com/forum/

Vitara carby on sierra 1.3
https://auszookers.com/forum/viewtopic.php?f=5&t=24702		 Page 1 of 1
Author:  zooker [ Wed Aug 10, 2011 3:31 am ]
Post subject:  Vitara carby on sierra 1.3
I've just replaced my sierra carby and inlet manifold with one off a G16A vitara carby engine. I have three questions to those that have done this before:

1. Do you have to use the vitara accelerator cable or modify the sierra one? The cable I have is too long as the mounting for it on the vit carby is further over than on the sierra carb.

2. Where is this vacuum hose meant to hook up to. It comes out of the bottom of the passenger side of the carb, where three vac hoses come out together. It then loops around the front of the carb and over the thermostat housing.

Image
Image

3. Whats this hose for? I've blocked it off as there's nowhere on a sierra for it.

Image
Author:  Reubs [ Wed Aug 10, 2011 3:38 am ]
Post subject:  Re: Vitara carby on sierra 1.3
Hose no.3 goes into the charcoal canister (mounted above the steering box in a Vitara instead of the firewall in a Sierra).

Not sure of the others without having a look at my vehicles.
Author:  zooker [ Wed Aug 10, 2011 3:40 am ]
Post subject:  Re: Vitara carby on sierra 1.3
Ah thanks for that. I'll just leave it blocked then
Author:  zooker [ Fri Aug 12, 2011 6:12 am ]
Post subject:  Re: Vitara carby on sierra 1.3
bump

Surely someone has done this mod
Author:  SierraDan [ Fri Aug 12, 2011 7:05 am ]
Post subject:  Re: Vitara carby on sierra 1.3
The bottom picture looks the same as my valve cover breather...
Author:  turbo_deo [ Fri Aug 12, 2011 7:11 am ]
Post subject:  Re: Vitara carby on sierra 1.3
I have a g16a in my zook I will try and have a look for you tonight and report back :helloo:

Edit:I think number one runs to the airbox possibly? Will double check this

number 2 on mine is looped between two of the nipples where it comes off the carby, I will get some photos for you tomorrow
Author:  BlueSuzy [ Fri Aug 12, 2011 8:09 am ]
Post subject:  Re: Vitara carby on sierra 1.3
Get efi
Author:  zooker [ Mon Aug 15, 2011 2:30 am ]
Post subject:  Re: Vitara carby on sierra 1.3
BlueSuzy wrote:
Get efi


sell me a cheap efi engine Armsup
Author:  deegs88 [ Tue Aug 16, 2011 8:11 am ]
Post subject:  Re: Vitara carby on sierra 1.3
do you have more power after you put the vitara carby in
Author:  mavmitchell [ Tue Aug 16, 2011 10:51 am ]
Post subject:  Re: Vitara carby on sierra 1.3
Hi,

The small hose(one of the 3) goes to the canister, 1 to the vac advance, and 1 to the EGR.(yours is already in place)
The sierra Canaster only has 2 pipes on it, one to the tank vent and this one(purge line).

The large hose from the top of the carb(number 3) is the carb vent, but only when the engine is not running. The Small solenoid on top of the carb vents the float chamber to the throat during running, and this pipe when turned off..
Author:  BlueSuzy [ Tue Aug 16, 2011 1:30 pm ]
Post subject:  Re: Vitara carby on sierra 1.3
zooker wrote:
BlueSuzy wrote:
Get efi


sell me a cheap efi engine Armsup


I need mine as spare, Since everything that turns into a big problem tends to happen with you. :mrgreen:

Overheat motor. check
Blow rear diff. check

:peaceout:
Author:  Brett [ Sat Dec 10, 2011 11:20 pm ]
Post subject:  Re: Vitara carby on sierra 1.3
i have a question, what heater hose do i block off? there is 3 on the carby and only 2 in the sierra.
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/