its called a geniric scan tool.....
I think snap-on does one, you buy the unit then buy keys for each different vehicle
| auszookers.com https://auszookers.com/forum/ |
|
| error code finder thingo https://auszookers.com/forum/viewtopic.php?f=5&t=24815 |
Page 1 of 2 |
| Author: | shep [ Sun Aug 14, 2011 12:10 pm ] |
| Post subject: | error code finder thingo |
whats the thing called that reads the error codes on efi motors and would it be the same tool for a 91 16v g16 vitara and a current model 2.4 gv. also where can i buy one? |
|
| Author: | joel [ Sun Aug 14, 2011 12:15 pm ] |
| Post subject: | Re: error code finder thingo |
its called a geniric scan tool.....
I think snap-on does one, you buy the unit then buy keys for each different vehicle
|
|
| Author: | stewy91 [ Sun Aug 14, 2011 12:18 pm ] |
| Post subject: | Re: error code finder thingo |
it's called a Generic Scan Tool I'm not sure if it is compatible possible you could just get different plugs but not sure. |
|
| Author: | nato78 [ Sun Aug 14, 2011 12:29 pm ] |
| Post subject: | Re: error code finder thingo |
I think snap-on does one, you buy the unit then buy keys for each different vehicle |
|
| Author: | shandy92 [ Sun Aug 14, 2011 12:44 pm ] |
| Post subject: | Re: error code finder thingo |
ahaha, 3 responses with the same thing. so why not add another. im pretty sure snap-on make one, its called a Scan tool. you need a different key for each vehicle tho. you just "scan" the tool over the engine, as close to the rocker cover as possible and it read all the failures happening inside. it must have x-ray vision or something to see whats going on.  
|
|
| Author: | mnemonix [ Sun Aug 14, 2011 12:45 pm ] |
| Post subject: | Re: error code finder thingo |
If the vehicle in questions uses OBD-II (on board diagnostics port) you can pick up a generic scan tool from ebay for under $100. The snap-on one recommended above is about $10k with all of the keys for full vehicle coverage. |
|
| Author: | McBane [ Sun Aug 14, 2011 1:23 pm ] |
| Post subject: | Re: error code finder thingo |
Snapon do one for about $2500 that will do most stuff its called an ethos |
|
| Author: | Scrawny [ Sun Aug 14, 2011 6:32 pm ] |
| Post subject: | Re: error code finder thingo |
I use the one sold by Repco. $150. Talks to maybe 60% of vehicles? It will usually spit out the code but can't tell you what it means, google will fix that tho |
|
| Author: | Bruce [ Sun Aug 14, 2011 7:58 pm ] |
| Post subject: | Re: error code finder thingo |
I have one of these. Bloody good. The ScanGauge II can check for Diagnostic Trouble Codes (DTCs) and if found, can display how many there are and the Trouble Codes themselves. Using the internet or repair manuals, these can be translated to the failed component and repairs can be made. Data captured when the Trouble Code was set can be recalled to help troubleshoot the problems (was the temperature hot or cold, speed high or low, etc.). The ScanGauge II can be used to clear the trouble codes and data which will turn off the warning (Check Engine, Service Engine soon, etc.) lamp. Does lots of other cool stuff as well. http://www.scangauge.com.au/products/ |
|
| Author: | Jester [ Sun Aug 14, 2011 8:16 pm ] |
| Post subject: | Re: error code finder thingo |
though current model GV is CAN BUS so a lot of basic generic stuff may struggle, without the right protocols |
|
| Author: | royce [ Sun Aug 14, 2011 8:48 pm ] |
| Post subject: | Re: error code finder thingo |
Dear Shep Ignore this thread, unless Stekky or Rhinoman post the 1.6 there is no tool needed, you just short 2 pins on s plug and the check engine light flashes to tell you whats going on That later one wont be a problem while you own it 
A lot of Suzuki's AREN'T OBDII so the generic stuff doesnt work |
|
| Author: | Bruce [ Sun Aug 14, 2011 8:53 pm ] |
| Post subject: | Re: error code finder thingo |
Well I'll just crawl back into my hole again. |
|
| Author: | Rockhopper [ Sun Aug 14, 2011 9:04 pm ] |
| Post subject: | Re: error code finder thingo |
royce wrote: A lot of Suzuki's AREN'T OBDII so the generic stuff doesnt work
Hey Royce, does this include the twin cam Jimny's?? I got supplied one of these http://www.rennacs.com/products.php#bluetooth through work and I can't get it to communicate with the Jim, but has no problems with most other cars. |
|
| Author: | royce [ Sun Aug 14, 2011 9:04 pm ] |
| Post subject: | Re: error code finder thingo |
Bruce wrote: Well I'll just crawl back into my hole again.
And dont come out without asking this time! |
|
| Author: | FullyZooked [ Sun Aug 14, 2011 9:55 pm ] |
| Post subject: | Re: error code finder thingo |
I've seen some pretty Inventive two pin "code pulling tools". Eg. Coathangers bent to shape like Ataris masterpeice. I'm sure he will be able to post a pick for you 
|
|
| Author: | royce [ Sun Aug 14, 2011 10:26 pm ] |
| Post subject: | Re: error code finder thingo |
Rockhopper wrote: royce wrote: A lot of Suzuki's AREN'T OBDII so the generic stuff doesnt work Hey Royce, does this include the twin cam Jimny's?? I got supplied one of these http://www.rennacs.com/products.php#bluetooth through work and I can't get it to communicate with the Jim, but has no problems with most other cars. It could do, I dont know which (if any) Suzuki are real OBDII I have this http://www.auszookers.com/index.php?nam ... diagnostic Maybe try that software with your unit? but then I think the pinouts differ too from memory |
|
| Author: | birko [ Mon Aug 15, 2011 1:10 pm ] |
| Post subject: | Re: error code finder thingo |
Yep as above (as in normal scan tools dont work), All you need is a bit of wire! I followed the guide on rhinopower.org Of course you need the diagnostics plug and check engine light wired up but. I also bought a cable of rhinopower to use with his free software. |
|
| Author: | shep [ Mon Aug 15, 2011 1:17 pm ] |
| Post subject: | Re: error code finder thingo |
thanks for the info that is right and you lot that wanted me to give the snapon man a few grand for a tool that i couldn't use can get a big dog up yas. |
|
| Author: | atari4x4 [ Mon Aug 15, 2011 1:25 pm ] |
| Post subject: | Re: error code finder thingo |
Shep, send me $1,247.33+ GST (gus' service tax) & i will supply you with a custom made error code reader 
Attached is a word document explaining how to use the hi tech device.
|
|
| Author: | dave91 [ Mon Aug 15, 2011 10:03 pm ] |
| Post subject: | Re: error code finder thingo |
royce wrote: Rockhopper wrote: royce wrote: A lot of Suzuki's AREN'T OBDII so the generic stuff doesnt work Hey Royce, does this include the twin cam Jimny's?? I got supplied one of these http://www.rennacs.com/products.php#bluetooth through work and I can't get it to communicate with the Jim, but has no problems with most other cars. It could do, I dont know which (if any) Suzuki are real OBDII I have this http://www.auszookers.com/index.php?nam ... diagnostic Maybe try that software with your unit? but then I think the pinouts differ too from memory What does OBDII mean? When my integra was showing an error code I got my mechanic to diagnose it, his flash snap setup was $24,000.. Looks like he got a bad deal!! |
|
| Author: | Scrawny [ Mon Aug 15, 2011 10:51 pm ] |
| Post subject: | Re: error code finder thingo |
OBDII = On Board Diagnostics. It's becoming standard across most vehicles now. II just means version 2. |
|
| Author: | sogone [ Tue Aug 16, 2011 4:39 am ] |
| Post subject: | Re: error code finder thingo |
joel wrote: its called a geniric scan tool.....
I think snap-on does one, you buy the unit then buy keys for each different vehicle ???????????????????????? ??????????????????????? ????????????????????? ???????????????????? ^^ this was meant to be the fail whale... but it didn't work. |
|
| Author: | bailey08 [ Tue Aug 16, 2011 6:07 am ] |
| Post subject: | Re: error code finder thingo |
I have a cheap ebay bluetooth adapter for $17 and "torque" android app(free version), unfortuatly 02 gv was not OBDII compliant in australia. Works perfect on alot of cars though. |
|
| Author: | Rockhopper [ Fri Aug 19, 2011 10:24 pm ] |
| Post subject: | Re: error code finder thingo |
royce wrote: Rockhopper wrote: royce wrote: A lot of Suzuki's AREN'T OBDII so the generic stuff doesnt work Hey Royce, does this include the twin cam Jimny's?? I got supplied one of these http://www.rennacs.com/products.php#bluetooth through work and I can't get it to communicate with the Jim, but has no problems with most other cars. It could do, I dont know which (if any) Suzuki are real OBDII I have this http://www.auszookers.com/index.php?nam ... diagnostic Maybe try that software with your unit? but then I think the pinouts differ too from memory I will try this when I get some time. I don't thin it'll work but you never know |
|
| Author: | Moag [ Sun Aug 21, 2011 11:41 pm ] |
| Post subject: | Re: error code finder thingo |
This is as far as I've got with understanding my little bus!! 
|
|
| Author: | Rhinoman [ Tue Aug 23, 2011 11:29 am ] |
| Post subject: | Re: error code finder thingo |
"OBD2" is actually a US standard* mandated in 1996, that standard didn't include KWP2000 or CAN but has since been superceded. The European standard which did include KWP2000 is often referred to as EOBD but despite difference in the data communications and hardware all the protocols transmiut the same basic data. From 2006 Australia adopted Euro 4 regulations which means that any generic scan tool that covers ISO9141-2 and KWP2000 (ISO14230) should work but many generic toools fail to connect properly to KWP2000 and need to have ISO14230 (Fast init) manually selected. I'm not sure when CANbus was adopted in Aus but again a generic tool should work. Prior to 2006 its a bit fuzzy, some vehicles have SDL, the original Suzuki proprietary format, some use ISO9141-2 an OBD2 standard and others use a Suzuki proprietary format based on KWP2000 called SDL-KWP. I have been working on SDL-KWP but I haven't been able to get my hands on an ECU to test. Incidentally if you're using CANBus with a laptop interface always use the internal battery only - plugging the laptop into the mains is a good way to smoke the ECU. * In actuality its a collection of around 12 standards that includes, IIRC, five different protocols. |
|
| Author: | swifty_ano [ Thu Nov 24, 2011 4:27 am ] |
| Post subject: | Re: error code finder thingo |
Hey I just tried the diagnostic on my g16B. engine light flash 3 times paused and flashed 4 times. Can anyone tell me what error this is?? |
|
| Author: | Ben_Sierra [ Thu Nov 24, 2011 4:30 am ] |
| Post subject: | Re: error code finder thingo |
Error code 34? |
|
| Author: | atari4x4 [ Thu Nov 24, 2011 4:32 am ] |
| Post subject: | Re: error code finder thingo |
there is a pdf attached to my earlier post, download it & find the code on the list.
|
|
| Author: | Ben_Sierra [ Thu Nov 24, 2011 4:32 am ] |
| Post subject: | Re: error code finder thingo |
http://kick-fix.com/ECU/DTC-errors/DTC-jtgh.html Google is your friend.. This is for US sidekicks, may be the same? 34: MAF (16valve only) Air Flow Sensor Circuit ,too low current. , lower than 0.65mA detected EDIT: This aligns with atari's document too... |
|
| Page 1 of 2 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|