You don't need a torque wrench
Just a feeler gauge, flathead screwdriver and 12mm ring spanner. 
| auszookers.com https://auszookers.com/forum/ |
|
| valve ajustment https://auszookers.com/forum/viewtopic.php?f=5&t=24959 |
Page 1 of 1 |
| Author: | matty [ Sat Aug 20, 2011 12:47 am ] |
| Post subject: | valve ajustment |
need help on valve ajustment on a sohc g 16 b . thanks all. |
|
| Author: | zukmeista [ Sat Aug 20, 2011 12:50 am ] |
| Post subject: | Re: valve ajustment |
What do you need to know? |
|
| Author: | matty [ Sat Aug 20, 2011 12:55 am ] |
| Post subject: | Re: valve ajustment |
clearence/ inllet and exhaust |
|
| Author: | SierraDan [ Sat Aug 20, 2011 1:40 am ] |
| Post subject: | Re: valve ajustment |
COLD- Inlet: 0.13-0.17 Exhaust: 0.16-0.20 HOT- Inlet: 0.23-0.27 exhaust: 0.26-0.30 |
|
| Author: | zukmeista [ Sat Aug 20, 2011 1:54 am ] |
| Post subject: | Re: valve ajustment |
SierraDan wrote: COLD- Inlet: 0.13-0.17
Exhaust: 0.16-0.20 HOT- Inlet: 0.23-0.27 exhaust: 0.26-0.30 That's for a G13A. Are they the same? |
|
| Author: | SierraDan [ Sat Aug 20, 2011 2:28 am ] |
| Post subject: | Re: valve ajustment |
zukmeista wrote: SierraDan wrote: COLD- Inlet: 0.13-0.17 Exhaust: 0.16-0.20 HOT- Inlet: 0.23-0.27 exhaust: 0.26-0.30 That's for a G13A. Are they the same? Ooh. Dyslexia kicked in. |
|
| Author: | Vits93 [ Sat Aug 20, 2011 3:44 am ] |
| Post subject: | Re: valve ajustment |
zukmeista wrote: SierraDan wrote: COLD- Inlet: 0.13-0.17 Exhaust: 0.16-0.20 HOT- Inlet: 0.23-0.27 exhaust: 0.26-0.30 That's for a G13A. Are they the same? They are a bit different. cold intake 0.13 - 0.17 (0.005" - 0.007") exhaust 0.23 - 0.27 (0.009" - 0.011") hot intake 0.17 - 0.21 (0.007" - 0.008") exhaust 0.28 - 0.32 (0.011" - 0.013") |
|
| Author: | shane1992 [ Sat Aug 20, 2011 8:05 am ] |
| Post subject: | Re: valve ajustment |
how hard is this to do? is it just feeler gagues that are used? |
|
| Author: | SierraDan [ Sat Aug 20, 2011 8:56 am ] |
| Post subject: | Re: valve ajustment |
shane1992 wrote: how hard is this to do? is it just feeler gagues that are used? and torque wrench
|
|
| Author: | zukmeista [ Sat Aug 20, 2011 8:04 pm ] |
| Post subject: | Re: valve ajustment |
You don't need a torque wrench Just a feeler gauge, flathead screwdriver and 12mm ring spanner.
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|