| auszookers.com https://auszookers.com/forum/ |
|
| G16b timing belt prob https://auszookers.com/forum/viewtopic.php?f=5&t=25782 |
Page 1 of 1 |
| Author: | Drova [ Wed Sep 14, 2011 4:42 am ] |
| Post subject: | G16b timing belt prob |
Hey, am replacing my timing belt I've followed the Correct process tensioning the belt, tensioner bolt finger tight, 2x cranks to get correct tension, tighten Tensioner stud followed by the tensioner bolt. BUT When I crank it over with the starter the belt starts To walk off the pullys( I've repeated the process 3 times) Can anyone help, with what might be causing this? Thanks luke |
|
| Author: | royce [ Wed Sep 14, 2011 4:44 am ] |
| Post subject: | Re: G16b timing belt prob |
you havent seated one of the pulleys back on square, pull em off and make sure they are square and you also have the big bolt in on the crank pulley |
|
| Author: | Drova [ Wed Sep 14, 2011 4:46 am ] |
| Post subject: | Re: G16b timing belt prob |
Thanks, blots on the bottom, I'll remove the pulleys And check now |
|
| Author: | Drova [ Wed Sep 14, 2011 5:22 am ] |
| Post subject: | Re: G16b timing belt prob |
Am sure that the pulleys are seated well, but still Belt walks, are timing belts directional because no Markings on this one? |
|
| Author: | royce [ Wed Sep 14, 2011 5:31 am ] |
| Post subject: | Re: G16b timing belt prob |
Sombody once told me to always fit them with the writing so it was the right way to read it when standing at the front of the engine Only other thing I can think of is the belt too tight or tensioner loose so the idler is flexing How far off the pulley have you let it get? |
|
| Author: | Drova [ Wed Sep 14, 2011 5:45 am ] |
| Post subject: | Re: G16b timing belt prob |
Yes that's the way I always fit belts, so The writing goes the same way the motor Cranks. The tensioners good, I'll fiddle with The belt tension till I get it right, I've done Them before on the 1.3 thanks mate |
|
| Author: | steak_knife [ Wed Sep 14, 2011 6:22 am ] |
| Post subject: | Re: G16b timing belt prob |
Drova wrote: Am sure that the pulleys are seated well, but still
Belt walks, are timing belts directional because no Markings on this one? Walking to the radiator or the eng??? Haven't left a guide of the belt pulley??? |
|
| Author: | Drova [ Wed Sep 14, 2011 6:39 am ] |
| Post subject: | Re: G16b timing belt prob |
It's walking towards the radiator |
|
| Author: | shandy92 [ Wed Sep 14, 2011 8:42 am ] |
| Post subject: | Re: G16b timing belt prob |
i have done mine 3 times and always done it, put the bottom pulley on and that holds it on. was told this by the boys at suzistore. just make sure that the belt is on evenly on top and bottom gears. |
|
| Author: | Drova [ Wed Sep 14, 2011 10:01 am ] |
| Post subject: | Re: G16b timing belt prob |
Yeah mate i worked that out, but your post is right on the money problem solved just needed to put the fan pulley on and fixed, Last time it was on old 1.3, so didn't care as much put it all on And it worked, but with the 16valve I was being careful so I was Checking it with the cover off so I didn't have the fan pulley on ether Thanks alot guys |
|
| Author: | shandy92 [ Wed Sep 14, 2011 10:10 am ] |
| Post subject: | Re: G16b timing belt prob |
yeah no worries mate, i was in the same place last time i did it. kept on adjusting the belt to try and make it run/walk straight but couldnt, spend almost an hr failing at it. rang suzistore and done. how long did it take you to do? did you do the water pump at the same time? |
|
| Author: | Drova [ Wed Sep 14, 2011 10:23 am ] |
| Post subject: | Re: G16b timing belt prob |
I only took me about 2hours but The problem doubled that lol That was coz I gave up for an hour Had some beer and think, and bingo I worked it out. Yeah also I did the Waterpump, cam & crank seals |
|
| Author: | shandy92 [ Wed Sep 14, 2011 11:44 am ] |
| Post subject: | Re: G16b timing belt prob |
oh gee thats pretty good lol. i did my timing belt in 4. another time i did my water pump in 4 again but then had to pull it all off due to not removing all of the old gasket and not sealing. ended up taking 11hrs lol. oh do you have a mate called mitch McG...... , has a GQ ute on 33 KM2's? |
|
| Author: | Drova [ Wed Sep 14, 2011 12:12 pm ] |
| Post subject: | Re: G16b timing belt prob |
I think a sierra might have a bit more Room to work, how l long does it take To get vitara radiator out? I can do it in The sierra in about 5mins now. Lol I've Had it out so many times. I might, I know Of guy with a white GQ ute but he's friend of a friend whys that? |
|
| Author: | shandy92 [ Wed Sep 14, 2011 1:12 pm ] |
| Post subject: | Re: G16b timing belt prob |
oh doesnt take long, prob 15mins max if you have done it b4. oh ok, thought i saw ur drover on his facebook page once, maybe not. sorry for chatting in the tech section. |
|
| Author: | Drova [ Wed Sep 14, 2011 1:34 pm ] |
| Post subject: | Re: G16b timing belt prob |
Was it out at skeet road? |
|
| Author: | shandy92 [ Wed Sep 14, 2011 1:37 pm ] |
| Post subject: | Re: G16b timing belt prob |
wheres that? not sure where but i thought it was out at mundaring. could be wrong tho. just tried to find pics but failed. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|