auszookers.com
https://auszookers.com/forum/

Will my a/c bolt up to a g16b?
https://auszookers.com/forum/viewtopic.php?f=5&t=26726		 Page 1 of 1
Author:  matfan [ Thu Oct 13, 2011 10:45 am ]
Post subject:  Will my a/c bolt up to a g16b?
Hi Guys,

About to do the g16 swap into my sierra, I'm currently running factory air con and just want to know if I'm wrong to assume that the compressor will bolt up to the 1.6??

Cheers
Author:  BlueSuzy [ Thu Oct 13, 2011 11:03 am ]
Post subject:  Re: Will my a/c bolt up to a g16b?
Is your g13b multiv?
Is your g16b multiv?

It may boltup, but the pulleys may differ! On mine im going to run a jimny compressor(multiv) with adaptor hoses to the sierra firewall/ac box..
Author:  CairnsZook [ Thu Oct 13, 2011 12:17 pm ]
Post subject:  Re: Will my a/c bolt up to a g16b?
Yes your AC pump bracket will bolt directly to the G16B.
But as BlueSuzy says, they pulleys are different. Sierra AC has a V pulley, G16B block has a ribbed pulley. You'll need to change the AC pulley to suit.
Author:  shep [ Thu Oct 13, 2011 7:30 pm ]
Post subject:  Re: Will my a/c bolt up to a g16b?
CairnsZook wrote:
Yes your AC pump bracket will bolt directly to the G16B.
But as BlueSuzy says, they pulleys are different. Sierra AC has a V pulley, G16B block has a ribbed pulley. You'll need to change the AC pulley to suit.


really? mine didn't and it didn't by a lot.

i would tell ya what i did to my aircon when i did the g16 conversion however you are a fuckwit so i wont :wink:
Author:  CairnsZook [ Thu Oct 13, 2011 7:43 pm ]
Post subject:  Re: Will my a/c bolt up to a g16b?
shep wrote:

really? mine didn't and it didn't by a lot.


Here's the Sierra AC bracket bolted directly onto the G16B. (bracket in front of oil filter)
Image

shep wrote:

i would tell ya what i did to my aircon when i did the g16 conversion however you are a fuckwit so i wont :wink:


err, ok. Thanks :roll:
Author:  shep [ Thu Oct 13, 2011 8:03 pm ]
Post subject:  Re: Will my a/c bolt up to a g16b?
my sierra bracket had 3 mounting points,one on the front of the motor and 2 on the side, the top side mount was out by about 25mm. if ya
dont think matfan is a fuckwit then ya should check out his old posts.
Author:  matfan [ Thu Oct 13, 2011 9:13 pm ]
Post subject:  Re: Will my a/c bolt up to a g16b?
Cheers guys, well hopefully it'll go on easily, if not I guess I'll have to make some sort of adapter out of matchsticks and clag glue.

Oh and I second sheps comment, I just had a bit of a read through some of my old posts.... I really am a fuckwit!
Author:  matfan [ Thu Oct 13, 2011 9:18 pm ]
Post subject:  Re: Will my a/c bolt up to a g16b?
Come to think of it, the clutch on the a/c compressor is a little bit dodge at the moment, I wonder if I could replace the whole clutch/pulley assembly with a multiV......
Author:  CairnsZook [ Thu Oct 13, 2011 11:07 pm ]
Post subject:  Re: Will my a/c bolt up to a g16b?
Ahh, I see...

Shep, didn't you have a different compressor though? Maybe a different bracket as well?
My bracket also has three holes, they all lined up perfectly.


Mat, one of these might work.
Author:  matfan [ Thu Oct 13, 2011 11:16 pm ]
Post subject:  Re: Will my a/c bolt up to a g16b?
Cheers for that, I guess I can save my matchsticks and clag glue for the exo build!
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/