Sounds like I'll be giving Suzistore a call.
| auszookers.com https://auszookers.com/forum/ |
|
| tacho not working https://auszookers.com/forum/viewtopic.php?f=5&t=26873 |
Page 1 of 1 |
| Author: | matty [ Tue Oct 18, 2011 7:25 am ] |
| Post subject: | tacho not working |
hi all, just got my zook back together and the only thing not working is the tacho. i'v checked all the fuses and everything i can think of but no luck. its a seirra with a g16b in it. any help or ideas would be great. thanks all |
|
| Author: | 11_evl [ Tue Oct 18, 2011 7:28 am ] |
| Post subject: | Re: tacho not working |
wire is near coil, is it hooked up |
|
| Author: | steak_knife [ Tue Oct 18, 2011 7:29 am ] |
| Post subject: | Re: tacho not working |
11_evl wrote: wire is near coil, is it hooked up
brown I think... |
|
| Author: | steak_knife [ Tue Oct 18, 2011 7:30 am ] |
| Post subject: | Re: tacho not working |
steak_knife wrote: 11_evl wrote: wire is near coil, is it hooked up brown I think... Wire that is... |
|
| Author: | matty [ Tue Oct 18, 2011 7:58 am ] |
| Post subject: | Re: tacho not working |
year all hooked up, put a test light on all wires i could see and they seem to be geting power. i will run a few more checks around the coil tommorrow and see what happens. thanks all. the car was in the shed for about 12 months so it may be a dodgy conection. |
|
| Author: | alien [ Tue Oct 18, 2011 8:09 am ] |
| Post subject: | Re: tacho not working |
mine needed a resistor/transistor/modulartronic device put between the tacho and the cable for it to get a reading... im using the g13bb computer and head, but its a similar setup isnt it? Suzistore have since worked out how to do it also, maybe see if you can buy the little sucker off them to install? |
|
| Author: | losfer [ Tue Oct 18, 2011 8:19 am ] |
| Post subject: | Re: tacho not working |
the wire goes to the negative side of the coil ! , and yeah its brown as stekky said , the wire that is .. |
|
| Author: | DMAC [ Tue Oct 18, 2011 7:25 pm ] |
| Post subject: | Re: tacho not working |
alien wrote: mine needed a resistor/transistor/modulartronic device put between the tacho and the cable for it to get a reading... im using the g13bb computer and head, but its a similar setup isnt it?
Suzistore have since worked out how to do it also, maybe see if you can buy the little sucker off them to install? Do you have more info on the modulatronic device? I've got the same issue using the GTi ECU. I attach the tacho wire and the engine dies. |
|
| Author: | alien [ Tue Oct 18, 2011 9:27 pm ] |
| Post subject: | Re: tacho not working |
no more info im afraid - a place near my house called "Applied Instruments" got mine working for $80... all i know is they pulled the cluster out and fitted a whatsydoover to convert the signal. Suzistore then sent a few conversions there and analysed what was done so now they can do it in house themselves. |
|
| Author: | DMAC [ Wed Oct 19, 2011 10:25 pm ] |
| Post subject: | Re: tacho not working |
Sounds like I'll be giving Suzistore a call.
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|