fatz wrote:
is there any non welding options for the 1.3?
Cheers
Cheers
No mate. Yor engine mounts are in the wrong spot. Either you make custom mounts, or you move the mounts on the rails.
| auszookers.com https://auszookers.com/forum/ |
|
| 1.6 into maruti question https://auszookers.com/forum/viewtopic.php?f=5&t=27153 |
Page 1 of 1 |
| Author: | fatz [ Thu Oct 27, 2011 12:17 am ] |
| Post subject: | 1.6 into maruti question |
Hey guys, Struggling to get my head around this.. I want to put either a 1.3 or 1.6 into my maruti to replace the F10a that is currently in there with a big end issue. Will this kit allow a 1.6 conversion to be bolt on? http://www.lowrangeoffroad.com/index.ph ... tegory/56/ is there any non welding options for the 1.3? Cheers |
|
| Author: | Fatzook [ Thu Oct 27, 2011 12:29 am ] |
| Post subject: | Re: 1.6 into maruti question |
fatz wrote: is there any non welding options for the 1.3?
Cheers No mate. Yor engine mounts are in the wrong spot. Either you make custom mounts, or you move the mounts on the rails.
|
|
| Author: | fatz [ Thu Oct 27, 2011 12:43 am ] |
| Post subject: | Re: 1.6 into maruti question |
No worries. Cheers |
|
| Author: | christover1 [ Thu Oct 27, 2011 4:01 am ] |
| Post subject: | Re: 1.6 into maruti question |
to fit a 1.3 into my 1.o Sierra I used 8 - 10 mm flat plate bolted to original chassis mounts, with holes drilled to match 1.3 engine mounts 1.6 could work same way? 
|
|
| Author: | Fatzook [ Thu Oct 27, 2011 4:45 am ] |
| Post subject: | Re: 1.6 into maruti question |
christover1 wrote: to fit a 1.3 into my 1.o Sierra
I used 8 - 10 mm flat plate bolted to original chassis mounts, with holes drilled to match 1.3 engine mounts 1.6 could work same way? Yes that could work, but the brackets would need to be longer still. |
|
| Author: | christover1 [ Thu Oct 27, 2011 5:03 am ] |
| Post subject: | Re: 1.6 into maruti question |
I was told it be shorter, but haven't actually measured it. But any longer than what I had, would be much too long I think one side is in same pozzy as a 1.3? |
|
| Author: | fatz [ Thu Oct 27, 2011 5:59 am ] |
| Post subject: | Re: 1.6 into maruti question |
nice one... thanks christover.. i will give it a go 
appreciate it. |
|
| Author: | christover1 [ Thu Oct 27, 2011 6:12 am ] |
| Post subject: | Re: 1.6 into maruti question |
I think some 1.o litre marutis have similar engine and gear box mounts to a 1.3 sierra, but only heard that, never seen one underneath |
|
| Author: | canberramav [ Thu Oct 27, 2011 6:45 am ] |
| Post subject: | Re: 1.6 into maruti question |
I just cut the mounts off a 1.3 chassis and welded them into the Maruti. I fitted a Gti so that all i had to do. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|