efi Vit cable....
| auszookers.com https://auszookers.com/forum/ |
|
| Baleno into Sierra https://auszookers.com/forum/viewtopic.php?f=5&t=27820 |
Page 1 of 1 |
| Author: | sogone [ Sat Nov 19, 2011 4:17 am ] |
| Post subject: | Baleno into Sierra |
How did everyone do their accelerator cables? Or what did you use. The stuff I have supplied just doesn't work out. Pj, supplied what he thought was a baleno accelerator but it just fit. Any ideas on what I can use to make this all work. |
|
| Author: | slowsierra [ Sat Nov 19, 2011 4:35 am ] |
| Post subject: | Re: Baleno into Sierra |
i used the standard cable and modified the sierra accel pedal greg |
|
| Author: | steak_knife [ Sat Nov 19, 2011 4:44 am ] |
| Post subject: | Re: Baleno into Sierra |
efi Vit cable....
|
|
| Author: | sogone [ Sat Nov 19, 2011 4:45 am ] |
| Post subject: | Re: Baleno into Sierra |
Even with the baleno throttle being completely different? |
|
| Author: | steak_knife [ Sat Nov 19, 2011 4:49 am ] |
| Post subject: | Re: Baleno into Sierra |
Pic......... tis in a different spot, but don't think it's that different that it won't fit/work |
|
| Author: | sogone [ Sat Nov 19, 2011 4:55 am ] |
| Post subject: | Re: Baleno into Sierra |
I tried changing the bracket round to make it work however it was then too long for the the adjustment nuts. 
And the supplied cable 
|
|
| Author: | BlueSuzy [ Sat Nov 19, 2011 5:08 am ] |
| Post subject: | Re: Baleno into Sierra |
slowsierra wrote: i used the standard cable and modified the sierra accel pedal
greg x2 If anything it was too long, Mine was down the back of the motor, Then up to the TB |
|
| Author: | steak_knife [ Sat Nov 19, 2011 5:26 am ] |
| Post subject: | Re: Baleno into Sierra |
That look's like a vit cable, try as the others have said.... |
|
| Author: | sogone [ Thu Dec 01, 2011 10:47 pm ] |
| Post subject: | Re: Baleno into Sierra |
Ok back to this. Can someone measure their Efi vit cable from ball bearing thingy to ball bearing thingy. The standard cable I have will not fit at all. Even Joel's brand new cable I borrowed from him for a g13ba will not fit. |
|
| Author: | BlueSuzy [ Thu Dec 01, 2011 11:11 pm ] |
| Post subject: | Re: Baleno into Sierra |
The baleno cable is straight at the throttle body side |
|
| Author: | tanshi [ Thu Dec 01, 2011 11:34 pm ] |
| Post subject: | Re: Baleno into Sierra |
I used a vit one i think, but shortened the inner using a brake cable end from a push bike shop. |
|
| Author: | sogone [ Thu Dec 01, 2011 11:47 pm ] |
| Post subject: | Re: Baleno into Sierra |
BlueSuzy wrote: The baleno cable is straight at the throttle body side
I don't have the stock baleno cable. Just the one supplied by pj.zook and one I pinched from Joel. Both identical. I'm not running a body life which probably answers why over all it too short. But it still itsnt long enough from the bracket to the throttle body 
Have you got a picture with what you mean tanshi? |
|
| Author: | sogone [ Sat Dec 10, 2011 11:08 am ] |
| Post subject: | Re: Baleno into Sierra |
Problem fixed. Probably not 'legal' in a sense but alot better IMO then dodging it with cable ties and what not. Used go kart cable joiner crimp joiner ma-bobby thingys. Got a pack of 5 for $6 or something. Cut the cables to length with slack spare on each side. Installed it then tightened it proper job when it was how I wanted it. Works a dream. 
Tidied it up after so no loose ends. 
Doesn't snag on anything and sits in the baleno stock accelerator holder bracket thing. |
|
| Author: | BlueSuzy [ Sun Dec 11, 2011 5:12 am ] |
| Post subject: | Re: Baleno into Sierra |
That will probably work fine. There is not much tension on throttle cables. |
|
| Author: | joel [ Sun Dec 11, 2011 5:27 am ] |
| Post subject: | Re: Baleno into Sierra |
not sure of legalities, but i doubt it would be a problem?? looks the goods, not like its a dodged break cable..... |
|
| Author: | sogone [ Sun Dec 11, 2011 9:39 am ] |
| Post subject: | Re: Baleno into Sierra |
I owe ya a new cable. Used yours in the end as well cause I cut mine too short 
|
|
| Author: | CairnsZook [ Sun Dec 11, 2011 9:40 am ] |
| Post subject: | Re: Baleno into Sierra |
I used the standard Baleno cable. Just had to mod the pedal end slightly to fit. |
|
| Author: | sogone [ Sun Dec 11, 2011 9:48 am ] |
| Post subject: | Re: Baleno into Sierra |
I didn't have the stock cable handy. Just had a g13ba one and a corolla 4k one. Made it flash as for $6. New baleno cable was gonna set me back $30 or something. |
|
| Author: | Brenno [ Sun Dec 11, 2011 9:55 am ] |
| Post subject: | Re: Baleno into Sierra |
I used a jimny cable when I put my jimny motor in, same manifold design. |
|
| Author: | BlueSuzy [ Sun Dec 11, 2011 9:57 am ] |
| Post subject: | Re: Baleno into Sierra |
Brenno wrote: I used a jimny cable when I put my jimny motor in, same manifold design.
How was the pedal? Um, I can look at my Jimny tomorrow..
|
|
| Author: | Brenno [ Sun Dec 11, 2011 9:39 pm ] |
| Post subject: | Re: Baleno into Sierra |
I used a jimny cable when I put my jimny motor in, same manifold design. |
|
| Author: | sogone [ Sun Dec 11, 2011 9:42 pm ] |
| Post subject: | Re: Baleno into Sierra |
Thanks brenno. Good advice 
|
|
| Author: | Brenno [ Sun Dec 11, 2011 9:47 pm ] |
| Post subject: | Re: Baleno into Sierra |
Just needed a small nut and bolt to squash the end in the pedal, |
|
| Author: | steak_knife [ Mon Dec 12, 2011 7:00 am ] |
| Post subject: | Re: Baleno into Sierra |
Simply because of the title, I'm going to put this here..... http://www.ptjau.com/images/sierra/bale ... ringv1.pdf |
|
| Author: | steak_knife [ Mon Dec 12, 2011 7:01 am ] |
| Post subject: | Re: Baleno into Sierra |
Oh, thanks to P.J.Zook....
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|