What engine
| auszookers.com https://auszookers.com/forum/ |
|
| URGENT, URGENT https://auszookers.com/forum/viewtopic.php?f=5&t=27937 |
Page 1 of 1 |
| Author: | strop [ Tue Nov 22, 2011 8:34 am ] |
| Post subject: | URGENT, URGENT |
Hey, got the engine running but bloody Hell the pulley off the crank has an awful wobble.... what is causing this???? Bearing gone maybe?? Help would be great or insight would be great. |
|
| Author: | Brett [ Tue Nov 22, 2011 8:37 am ] |
| Post subject: | Re: URGENT, URGENT |
Lose or not sitting on the crank right |
|
| Author: | Rusho [ Tue Nov 22, 2011 8:37 am ] |
| Post subject: | Re: URGENT, URGENT |
What engine
|
|
| Author: | oozuk [ Tue Nov 22, 2011 8:40 am ] |
| Post subject: | Re: URGENT, URGENT |
is the pulley sitting on the keyway correctly ? are the bolts from the pulley to the crank pulley tight ? is the bottom main crank bolt tight ? |
|
| Author: | steak_knife [ Tue Nov 22, 2011 8:45 am ] |
| Post subject: | Re: URGENT, URGENT |
Is the eng from a wrecker's??? |
|
| Author: | strop [ Tue Nov 22, 2011 9:03 am ] |
| Post subject: | Re: URGENT, URGENT |
G16b and no its not from a wreakers... its at the big end bearing it appears as if the smaller cog off the timing belt isn't on straight.... been hitting on the block before by the looks of it.... |
|
| Author: | strop [ Tue Nov 22, 2011 9:29 am ] |
| Post subject: | Re: URGENT, URGENT |
Almost like it was dropped on it??? |
|
| Author: | steak_knife [ Tue Nov 22, 2011 9:32 am ] |
| Post subject: | Re: URGENT, URGENT |
Take em off & look for sign's of damage... |
|
| Author: | strop [ Tue Nov 22, 2011 10:50 am ] |
| Post subject: | Re: URGENT, URGENT |
yes there is damage to the block but its not rubbing the block know? as i turn it you can see its closer to the block another 180 degrees and its further, prob 1mm in difference, but once you have the pulley on it increases to about 2, 3mm... bit scary to watch, so is it a matter of pulling it off and putting it back on?? |
|
| Author: | strop [ Tue Nov 22, 2011 10:50 am ] |
| Post subject: | Re: URGENT, URGENT |
or is it the crank or bearing... |
|
| Author: | strop [ Tue Nov 22, 2011 10:56 am ] |
| Post subject: | Re: URGENT, URGENT |
need to get it off and had a look im guessing, but is a puller required, thanks for you input 
|
|
| Author: | strop [ Tue Nov 22, 2011 11:05 am ] |
| Post subject: | Re: URGENT, URGENT |
i should really read what i have spelt right through before i post it hehe |
|
| Author: | shandy92 [ Tue Nov 22, 2011 12:50 pm ] |
| Post subject: | Re: URGENT, URGENT |
mate slow down!!! there will be 4 or 5 small 10mm bolts that hold that pulley on, no puller required it will fall off without them. once its off make sure its not bent, dented or cracked. clean it up put it back on. oh and when you do them up, do it in a star pattern. dont go around as this wont help with the wobble. |
|
| Author: | neofitou [ Tue Nov 22, 2011 6:24 pm ] |
| Post subject: | Re: URGENT, URGENT |
http://www.auszookers.com/index.php?nam ... ic&t=27844 |
|
| Author: | LittleJeep [ Tue Nov 22, 2011 9:52 pm ] |
| Post subject: | Re: URGENT, URGENT |
neofitou wrote:
X2 this is what happened to my brothers g16b and it had the exact same symptom you're describing. not sure if he still has pics, but there was a big chunk out of the leading edge where the keyway goes and the keyway was munched too. i pulled the engine out put it on a engine stand, flipped it upside down and put another crank in it (he had a 1.6 carby bottom end sitting there). to change the crank over only took an afternoon, it was pulling the engine out that took time (all those EFI wires!) does it lack power? |
|
| Author: | strop [ Tue Nov 22, 2011 11:04 pm ] |
| Post subject: | Re: URGENT, URGENT |
Hey shandy, I have tried that last night but it was still no good, the pulley itself is straight, not bent. So I can see its the keyway, hope there isn't much damage, ill see tonight. Will it simply tap off? |
|
| Author: | shandy92 [ Wed Nov 23, 2011 8:59 am ] |
| Post subject: | Re: URGENT, URGENT |
strop wrote: Hey shandy, I have tried that last night but it was still no good, the pulley itself is straight, not bent. So I can see its the keyway, hope there isn't much damage, ill see tonight. Will it simply tap off?
alright mate, the pulley should fall of. if it doesnt then yeah just tap it off. |
|
| Author: | mrgtt34 [ Wed Nov 23, 2011 9:54 am ] |
| Post subject: | Re: URGENT, URGENT |
call racq they will tow it |
|
| Author: | atari4x4 [ Wed Nov 23, 2011 10:05 am ] |
| Post subject: | Re: URGENT, URGENT |
mrgtt34 wrote: call racq they will tow it
it's the Royal Automotive Association of SA (RAA) in SA & i believe he's just installed the motor & it's still in the garage. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|