| auszookers.com https://auszookers.com/forum/ |
|
| Some wt to nt questions.... https://auszookers.com/forum/viewtopic.php?f=5&t=28693 |
Page 1 of 1 |
| Author: | suzukikid [ Sat Dec 17, 2011 2:33 am ] |
| Post subject: | Some wt to nt questions.... |
Hey all i have a few questions....i have searched am well ovit it! 
Alright 1 does the whole diff asslembly bolt straight from a wt to a nt? as in are the spring plate doovers in the same spot? 2 the transfer case and gearbox are the same? just different length drive shafts? 3 do nt and wt springs fit in the hangers? Thats about it i think...cheers |
|
| Author: | suzukikid [ Sat Dec 17, 2011 2:34 am ] |
| Post subject: | Re: Some wt to nt questions.... |
Also should of put parts will come from a wt swb to a nt lwb....cheers |
|
| Author: | zooky08 [ Sat Dec 17, 2011 2:52 am ] |
| Post subject: | Re: Some wt to nt questions.... |
Spring perches on diffs are different. Transfer case will be different depend on what year model Nt your talking about Springs will fit in the hanger. Wt and Nt are the same |
|
| Author: | losfer [ Sat Dec 17, 2011 3:35 am ] |
| Post subject: | Re: Some wt to nt questions.... |
1 . no , also the ratio's are different if you are only changing 1 diff... 2 . the transfer uses different flanges but are the same , you can change the flanges , or you can use the wt intermediate shaft and short slip joints off the wt for front and rear driveshafts . the gearbox is the same but may have more switches which were used for emmision control etc , dont worry about plugging them in , it will work fine 3. yes |
|
| Author: | 86slowsierra [ Sat Dec 17, 2011 3:40 am ] |
| Post subject: | Re: Some wt to nt questions.... |
1. you might need longer brake lines in the front |
|
| Author: | Damo [ Sat Dec 17, 2011 3:53 am ] |
| Post subject: | Re: Some wt to nt questions.... |
I've been working on this myself and have some pics that illustrate some of the differences. I'll post something up tonight. |
|
| Author: | sideways [ Sat Dec 17, 2011 4:12 am ] |
| Post subject: | Re: Some wt to nt questions.... |
You'l need to sort out a hand brake too. NTs have them on the transfer and WTs have them on the back wheels. |
|
| Author: | SierraDan [ Sat Dec 17, 2011 4:17 am ] |
| Post subject: | Re: Some wt to nt questions.... |
You could run no handbrake on the WT diffs and continue to use the NT trans brake. |
|
| Author: | foolsp33d [ Sat Dec 17, 2011 4:34 am ] |
| Post subject: | Re: Some wt to nt questions.... |
keeping in mind the NT uses two lines to the rear diff, the WT uses one right!? |
|
| Author: | suzukikid [ Sat Dec 17, 2011 5:41 am ] |
| Post subject: | Re: Some wt to nt questions.... |
Im toyin around...there is a nt long wheel base on ebay with no motor or gear box....just thinkin i could pretty much chuck everything from mine in complete diffs and all and then just get longer drive shafts..... any way still early days! Cheers everyone keep em comin....as for hand break.....whats that? 
|
|
| Author: | dougies_tx5turbo [ Sat Dec 17, 2011 5:43 am ] |
| Post subject: | Re: Some wt to nt questions.... |
foolsp33d wrote: keeping in mind the NT uses two lines to the rear diff, the WT uses one right!?
i fix this by using NT master cycinder on one side and taking a little bit off the top of the WT back brake shoes. or you could just use your NT shoes, not to sure if this will work for WT rear handbrake as i used my NT T-case drum handbrake. |
|
| Author: | steak_knife [ Sat Dec 17, 2011 6:11 am ] |
| Post subject: | Re: Some wt to nt questions.... |
dougies_tx5turbo wrote: foolsp33d wrote: keeping in mind the NT uses two lines to the rear diff, the WT uses one right!? i fix this by using NT master cycinder on one side and taking a little bit off the top of the WT back brake shoes. or you could just use your NT shoes, not to sure if this will work for WT rear handbrake as i used my NT T-case drum handbrake. Or use N/T rear backing plat's & brake's...... W/t NEED'S the H/brake to "self adjust", with out it you out of peddle all the time 
Op..... the n/t & w/t perch's are in different position's, need to be moved & the inner driver's side U bolt will need to be replaced with a longer one... |
|
| Author: | suzukikid [ Sat Dec 17, 2011 6:30 am ] |
| Post subject: | Re: Some wt to nt questions.... |
well the missus has said im not biddin any higher then i have put in.....so i guess i will play the waiting game! |
|
| Author: | steak_knife [ Sat Dec 17, 2011 6:33 am ] |
| Post subject: | Re: Some wt to nt questions.... |
suzukikid wrote: well the missus has said im not biddin any higher then i have put in.....so i guess i will play the waiting game!
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|