auszookers.com
https://auszookers.com/forum/

What is wrong with this picture??
https://auszookers.com/forum/viewtopic.php?f=5&t=2886		 Page 1 of 1
Author:  Scrawny [ Sat Sep 06, 2008 12:28 am ]
Post subject:  What is wrong with this picture??
Image

Image

Apart from the obvious, is it the water pump wrong or the tensioner bearing? G16B 16 valve motor
Author:  lump_a_charcoal [ Sat Sep 06, 2008 12:30 am ]
Post subject:  Re: What is wrong with this picture??
You mean because the other side of the belt is touching this side?

It looks ok to me...

Hint - change the timing belt and water pump at the same time...
Author:  royce [ Sat Sep 06, 2008 12:36 am ]
Post subject:  Re: What is wrong with this picture??
whats a G16b twincam is a good start

I bet tensioner, I think all the waterpumps are the same in that area

looking at it the tensioner doesnt look right, do you have a front on pic?
Author:  Scrawny [ Sat Sep 06, 2008 12:39 am ]
Post subject:  Re: What is wrong with this picture??
royce wrote:
whats a G16b twincam is a good start


Suzuki 8O

I was thinking maybe it was a G13 tensioner??
Author:  lump_a_charcoal [ Sat Sep 06, 2008 12:43 am ]
Post subject:  Re: What is wrong with this picture??
Probably the same as the G13... Looks just like my one, in my 1300... I reckon the tensioner is right, what do you think the problem is with the pictures?
Author:  royce [ Sat Sep 06, 2008 12:46 am ]
Post subject:  Re: What is wrong with this picture??
they made a g16 twincam?

my single cam :) g16 16valve tensioner looks the same as a G13 one, and where that bolt is through the bearing doesnt look right

but I could be trippin too :oops:
Author:  Scrawny [ Sat Sep 06, 2008 12:51 am ]
Post subject:  Re: What is wrong with this picture??
royce wrote:
they made a g16 twincam?


Learnt something new didn't you :roll:

Or was it me? :oops:
Author:  lump_a_charcoal [ Sat Sep 06, 2008 12:54 am ]
Post subject:  Re: What is wrong with this picture??
ScrawnC wrote:
royce wrote:
they made a g16 twincam?


Learnt something new didn't you :roll:

Or was it me? :oops:


Bwaaha haaa haaa!

Does it have Hilux diffs too?
Author:  royce [ Sat Sep 06, 2008 1:00 am ]
Post subject:  Re: What is wrong with this picture??
ok so I looked at some pics, yes I am on drugs and thats how the tensioner is

are the pulleys on properly? is the belt rubbing on teh cover?

I wonder if the belt would run out there if both pulleys were on back to front
Author:  lump_a_charcoal [ Sat Sep 06, 2008 1:01 am ]
Post subject:  Re: What is wrong with this picture??
Could the bearing be on back to front? It looks like it has been like this for a while...
Author:  Scrawny [ Sat Sep 06, 2008 1:16 am ]
Post subject:  Re: What is wrong with this picture??
Looks like it has done a fair bit of running like this alright. I'm suprised the belt hasn't 'walked' off the pulley. You might be right Lump, the bearing could be on backwards. I just pulled it all off as I'm replacing belt, bearing and water pump.
I'm guessing the apprentice did this one :roll: :lol:




I had it stuck in my head that 16 valve was twin cam for some reason, even though I knew it only had one cam.... :roll: must be the drugs
Author:  royce [ Sat Sep 06, 2008 1:19 am ]
Post subject:  Re: What is wrong with this picture??
ooo now I looked at the pics properly :oops:

looks like the slot for the adjusting bolt thingo doesnt go round far enough, I once saw a 1.3 that it went too far so perhaps its a 1.3 one?
Author:  Scrawny [ Sat Sep 06, 2008 1:23 am ]
Post subject:  Re: What is wrong with this picture??
There was absolutely no adjustment for the belt, the tensioner wouldn't move to allow slack. You may be right Royce.

Sorry, no front on pics :oops:
Author:  nissvit [ Sat Sep 06, 2008 1:29 am ]
Post subject:  Re: What is wrong with this picture??
can't see much from the angle of the pic.

this is what the last one I pulled apart looked like..
Author:  royce [ Sat Sep 06, 2008 1:31 am ]
Post subject:  Re: What is wrong with this picture??
bloody arty photographer types :roll:

so its a single cam 16valve :wink:
MAKE SURE YOU DO THE FRIGGEN CRANK BOLT UP PROPERLY!!!!!!!

and have a look the woodruff key isnt already flogged
Author:  royce [ Sat Sep 06, 2008 1:32 am ]
Post subject:  Re: What is wrong with this picture??
bloody arty photographer types :roll:

so its a single cam 16valve :wink:
MAKE SURE YOU DO THE FRIGGEN CRANK BOLT UP PROPERLY!!!!!!!

and have a look the woodruff key isnt already flogged
Author:  lump_a_charcoal [ Sat Sep 06, 2008 1:33 am ]
Post subject:  Re: What is wrong with this picture??
Ah i see the problem now...

Yeah looks totally different to the 1.3 version i have, but remember there is another 1.3 motor, with a different water pump (dont know the number), maybe it is from one of those.
Author:  Scrawny [ Sat Sep 06, 2008 1:35 am ]
Post subject:  Re: What is wrong with this picture??
Thanks Chris,

mine is definately a G13 tensioner then. They had the spring horizontal and had moved the screw that secures the spring end to the hole you can see straight out from the bearing.
I've only just done a G13 timing belt and I thought this tensioner looked the same.
Author:  11_evl [ Sat Sep 06, 2008 1:44 am ]
Post subject:  Re: What is wrong with this picture??
isnt there 2 different thinkness timing belts, maybe u have everything to suit the thicker belt bar the tensioner bearing??
Author:  royce [ Sat Sep 06, 2008 1:47 am ]
Post subject:  Re: What is wrong with this picture??
there is 2 different tooth profiles, but timing belts are a bit universal so its possible somebody could get one too long or short or wide that still fit
Author:  just_cruizin [ Sat Sep 06, 2008 2:47 am ]
Post subject:  Re: What is wrong with this picture??
Man, stop finding things wrong with my engine OK
Author:  BlueSuzy [ Mon Sep 08, 2008 9:17 pm ]
Post subject:  Re: What is wrong with this picture??
Is that a slight oil leak i see?

Looks abit dusty/oily on the sump

Sori. Is that another problem with your motor? :lol:
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/