| auszookers.com https://auszookers.com/forum/ |
|
| jimny temp sender https://auszookers.com/forum/viewtopic.php?f=5&t=29982 |
Page 1 of 1 |
| Author: | ellis [ Sun Jan 29, 2012 4:50 pm ] |
| Post subject: | jimny temp sender |
i have got a type R temp gauge that im planing on putting in my jimny i was wondering how do i set it up the bottom left goes to the sender does anyone know what wire from the plug in the pics would be the sender wire i think ive got the right plug  bottom goes to earth and the bottom right to ignition but what are the top 2 wires for?? its says to put these to dash light circuit what does it mean by this any help much appreciated
|
|
| Author: | woo603 [ Sun Jan 29, 2012 6:11 pm ] |
| Post subject: | Re: jimny temp sender |
by putting to the dash light circuit it will allow the light to turn on when you turn your lights on so you can see your gauge at night |
|
| Author: | woo603 [ Sun Jan 29, 2012 6:13 pm ] |
| Post subject: | Re: jimny temp sender |
the black one is an earth red is light power so it only has power when light is turned on |
|
| Author: | ellis [ Sun Jan 29, 2012 6:16 pm ] |
| Post subject: | Re: jimny temp sender |
k thanks i just wasnt sure if the other power one would do that any ideas on what wire is the sender from the engine |
|
| Author: | ellis [ Sun Jan 29, 2012 11:57 pm ] |
| Post subject: | Re: jimny temp sender |
can any 1 tell me what wire is the sender?? |
|
| Author: | atari4x4 [ Mon Jan 30, 2012 8:55 am ] |
| Post subject: | Re: jimny temp sender |
you'll need to run the aftermarket sender that came with the gauge, it's resistance will be calibrated to the gauge. |
|
| Author: | ellis [ Mon Jan 30, 2012 11:59 am ] |
| Post subject: | Re: jimny temp sender |
where abouts do i put this in i couldnt see an area for it will i have to make a new hole? |
|
| Author: | ellis [ Tue Feb 21, 2012 9:17 pm ] |
| Post subject: | Re: jimny temp sender |
can i use a old wire from the stock sender or will i have to put the new sender in |
|
| Author: | atari4x4 [ Tue Feb 21, 2012 9:24 pm ] |
| Post subject: | Re: jimny temp sender |
no cause the wire goes to the stock gauge in the dashboard, leave it alone & wire up the new gauge following the instructions. you need to use the sender that came with the aftermarket gauge as it's resistance is calibrated to the temp range shown on the aftermarket gauge. |
|
| Author: | ellis [ Tue Feb 21, 2012 9:27 pm ] |
| Post subject: | Re: jimny temp sender |
ok do you know if there is a spot for the sender in a jimny as i think the stock sender is completely different to the one with the gauge |
|
| Author: | atari4x4 [ Tue Feb 21, 2012 9:29 pm ] |
| Post subject: | Re: jimny temp sender |
NFI i don't do jimny's why do you need an aftermarket gauge, maximum respect from the fast n furious crew? |
|
| Author: | ellis [ Tue Feb 21, 2012 9:34 pm ] |
| Post subject: | Re: jimny temp sender |
haha nar i bought the gauge and gauge holder for my sierra due to its temp gauge didnt work but i sold it and now i thort sence i bought it i may aswell put it to use and they read the temp better and let you know if the temp going up b4 the stock unit does |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|