I put a falcon alt on and used a g13bb bottom crank I think, swift water pump and maybe a g13bb water pump pulley.... Buggered if I know, look at my build
it's all in there...
| auszookers.com https://auszookers.com/forum/ |
|
| Power steer setup -pulleys https://auszookers.com/forum/viewtopic.php?f=5&t=30140 |
Page 1 of 1 |
| Author: | mcwilly [ Thu Feb 02, 2012 7:43 pm ] |
| Post subject: | Power steer setup -pulleys |
Just wondering what pulleys are required for the alternator and crank to run a vitara power steer setup? And if anyone has any? Also what belt no do people use? |
|
| Author: | 31zook [ Fri Feb 03, 2012 2:39 am ] |
| Post subject: | Re: Power steer setup -pulleys |
I put a falcon alt on and used a g13bb bottom crank I think, swift water pump and maybe a g13bb water pump pulley.... Buggered if I know, look at my build it's all in there...
|
|
| Author: | mcwilly [ Fri Feb 03, 2012 4:21 pm ] |
| Post subject: | Re: Power steer setup -pulleys |
Pulleys sorted. Next question which pitman arm do u use sierra or vitara? |
|
| Author: | christover1 [ Fri Feb 03, 2012 6:08 pm ] |
| Post subject: | Re: Power steer setup -pulleys |
I used the Vitara pitman arm, for no reason other than it was too hard to remove, and it fit perfectly. There are other choices, like Tarrago pitmans and low range pitmans, but this does depend onn what other mods you have/intend. |
|
| Author: | mcwilly [ Fri Feb 03, 2012 6:30 pm ] |
| Post subject: | Re: Power steer setup -pulleys |
so the sierra one doesn't fit on? Are they different splines? Does the steering dampener fit with the vit pitman |
|
| Author: | christover1 [ Fri Feb 03, 2012 6:38 pm ] |
| Post subject: | Re: Power steer setup -pulleys |
mcwilly wrote: so the sierra one doesn't fit on? Are they different splines? Does the steering dampener fit with the vit pitman I did not try a Sierra pitman, so can't answer that. There is no mount for the steering damper on a Vitara pitmam arm. Never got round to fitting one, it was fine with out one. The fluid of power steer must act like a damper? |
|
| Author: | christover1 [ Fri Feb 03, 2012 6:41 pm ] |
| Post subject: | Re: Power steer setup -pulleys |
My ps instal pix, if they help http://s129.photobucket.com/albums/p237 ... ing%20pix/ |
|
| Author: | mcwilly [ Fri Feb 03, 2012 6:53 pm ] |
| Post subject: | Re: Power steer setup -pulleys |
Thanks mate I'll give the vit pitman a go. What belt will I need |
|
| Author: | ajsr [ Fri Feb 03, 2012 6:57 pm ] |
| Post subject: | Re: Power steer setup -pulleys |
measure around the pulleys in mm the belt will be a 4pk? by mm you measured ie 4pk1245 if its 1245 mm long |
|
| Author: | christover1 [ Fri Feb 03, 2012 7:00 pm ] |
| Post subject: | Re: Power steer setup -pulleys |
mcwilly wrote: Thanks mate I'll give the vit pitman a go. What belt will I need Have you gone multi V or single V belt? Think mine was 3 or 4PK 815, but it was a while ago. Run a string round it, to get approx length, that, and number of ribs is all an auto shop needs. |
|
| Author: | mcwilly [ Fri Feb 03, 2012 7:10 pm ] |
| Post subject: | Re: Power steer setup -pulleys |
Pump has 4pk pulley and I'm getting the spidertrax crank pulley. So then just measure those and away I go |
|
| Author: | christover1 [ Fri Feb 03, 2012 7:18 pm ] |
| Post subject: | Re: Power steer setup -pulleys |
mcwilly wrote: Pump has 4pk pulley and I'm getting the spidertrax crank pulley. So then just measure those and away I go Pretty sure mine was a stock Vitara power steering (non air con) belt. But yes, get it all in position and measure it |
|
| Author: | Rusho [ Fri Feb 03, 2012 7:21 pm ] |
| Post subject: | Re: Power steer setup -pulleys |
I doubt you will need a steering dampner with power steering. JMO 
|
|
| Author: | mcwilly [ Fri Feb 03, 2012 8:54 pm ] |
| Post subject: | Re: Power steer setup -pulleys |
Awesome just gotta get the brackets and it will be goin in. Can u use them with out the pump if need be |
|
| Author: | 31zook [ Sat Feb 04, 2012 1:46 am ] |
| Post subject: | Re: Power steer setup -pulleys |
Yep, you can run a PS box without the pump as long as it's capped off. |
|
| Author: | Rusho [ Sat Feb 04, 2012 5:09 am ] |
| Post subject: | Re: Power steer setup -pulleys |
31zook wrote: Yep, you can run a PS box without the pump as long as it's capped off. I wouldn't....be a good way to bugger the box I would have thought  I could be wrong though
|
|
| Author: | 31zook [ Sat Feb 04, 2012 9:46 am ] |
| Post subject: | Re: Power steer setup -pulleys |
Rusho wrote: 31zook wrote: Yep, you can run a PS box without the pump as long as it's capped off. I wouldn't....be a good way to bugger the box I would have thought I could be wrong thoughHow would it damage the box? |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|