| auszookers.com https://auszookers.com/forum/ |
|
| H25A Extractors https://auszookers.com/forum/viewtopic.php?f=5&t=31535 |
Page 1 of 1 |
| Author: | ninjamoses [ Thu Mar 29, 2012 6:06 pm ] |
| Post subject: | H25A Extractors |
As far as I know these are a fairly new item on the market (or if they aren't there is stuff all information on the net about them anyway) so thought I would throw up a thread/photos in case anyone else is interested. Purchased from Suzistore for $495: http://www.suzistore.com.au/shopexd.asp?id=1951 They are manufactured by Wildcat. Haven't fitted them yet but build quality seems pretty good to me.        
|
|
| Author: | Polar_Bear [ Thu Mar 29, 2012 6:11 pm ] |
| Post subject: | Re: H25A Extractors |
thanks for the heads up bro, i looked about 6 months ago and couldnt find anyone who made them without going custom 
|
|
| Author: | thesupervisor [ Thu Mar 29, 2012 6:31 pm ] |
| Post subject: | Re: H25A Extractors |
i have these on my gv i went a 2 1/4 pipe with a high flow cat and muffler made it more gruntyer for a week untill i got used to the power you may throw a engine light on the dash too i had to replace exughst sensor and cleaned all the throttle ones |
|
| Author: | shabz [ Thu Mar 29, 2012 7:16 pm ] |
| Post subject: | Re: H25A Extractors |
Good to know. Cheers ninja 
|
|
| Author: | thesupervisor [ Thu Mar 29, 2012 7:20 pm ] |
| Post subject: | Re: H25A Extractors |
be intrested in how many klms out of a tank you get with them i just get 400km but off roading its about 340km |
|
| Author: | dawsey [ Thu Mar 29, 2012 7:55 pm ] |
| Post subject: | Re: H25A Extractors |
they look good,well made brand,I have wildcat headers on my old 1.3 with 2inch pipe and hi flo cat..made the world of difference.. |
|
| Author: | Chop [ Thu Mar 29, 2012 9:14 pm ] |
| Post subject: | Re: H25A Extractors |
Thats a good price coz i found this http://www.bestmufflers.com/bshop/produ ... 9ca2034994 |
|
| Author: | Joe [ Thu Mar 29, 2012 9:20 pm ] |
| Post subject: | Re: H25A Extractors |
I paid $425 for J20 ones so $495 for them is a bargain |
|
| Author: | Aferal [ Fri Mar 30, 2012 10:23 pm ] |
| Post subject: | Re: H25A Extractors |
Was look at the headers and Y pipe on my GV thinking to myself they were a very poor design. These look a lot better not a bad price either. |
|
| Author: | MacDaddy [ Sat Mar 31, 2012 4:39 am ] |
| Post subject: | Re: H25A Extractors |
Aferal wrote: Was look at the headers and Y pipe on my GV thinking to myself they were a very poor design. These look a lot better not a bad price either. Actually, our resident Zook/GV expert, Mr steak_knife, recons the stock exhaust manifold on the GV is pretty damn good... and that putting extractors on, would gain very minimal results... which is why i went with straight thru exhaust an hiflo caty, from the Y joint back instead... but having said that, if i didnt want to get so many other things for my GV, i would definitely get them just for the Cool factor alone, hehe... 
|
|
| Author: | Built4thrashing [ Sat Mar 31, 2012 8:23 am ] |
| Post subject: | Re: H25A Extractors |
Do the H27 manifolds and y junction fit the H25? Are they any different? |
|
| Author: | Chop [ Sat Mar 31, 2012 7:09 pm ] |
| Post subject: | Re: H25A Extractors |
thesupervisor wrote: i have these on my gv i went a 2 1/4 pipe with a high flow cat and muffler made it more gruntyer for a week untill i got used to the power you may throw a engine light on the dash too i had to replace exughst sensor and cleaned all the throttle ones Got the dyno read out you were gonna put up? |
|
| Author: | thesupervisor [ Sun Apr 01, 2012 1:46 pm ] |
| Post subject: | Re: H25A Extractors |
no havent done the second run yet must get around to that once the diff and transfer is fixed will do |
|
| Author: | BlueSuzy [ Sun Apr 01, 2012 2:06 pm ] |
| Post subject: | Re: H25A Extractors |
Are the H manifolds normally cast or tube? Wildcats look good, if you scrape the paint, paint it again..They surface rust real quick. Might have something to do with where they are made. |
|
| Author: | ninjamoses [ Sun Apr 01, 2012 3:28 pm ] |
| Post subject: | Re: H25A Extractors |
Standard ones are cast manifolds with tube y pipe. |
|
| Author: | BlueSuzy [ Sun Apr 01, 2012 3:41 pm ] |
| Post subject: | Re: H25A Extractors |
ah ok thanks. I know most motors are cast. I know a 1uzfe is tube/pipe! |
|
| Author: | Mick70b [ Sun Apr 01, 2012 6:11 pm ] |
| Post subject: | Re: H25A Extractors |
I like the look of these a lot. Can anyone see any reason why these won't fit my H20A V6 in a SV620 ??? |
|
| Author: | tombutt [ Sun Apr 01, 2012 6:52 pm ] |
| Post subject: | Re: H25A Extractors |
i have been thinking the same thing as far as im aware you can bolt the h20 manifolds to the h25 when u do a conversion so it would just be the y pipes that may not fit how ever its the same gear box and such so should fit around that |
|
| Author: | twitchy [ Sun Apr 01, 2012 7:06 pm ] |
| Post subject: | Re: H25A Extractors |
Wildcat are a branch of Genie, so Id say they will be a decent set of extractors. |
|
| Author: | TheOtherLeft [ Tue Apr 03, 2012 11:42 am ] |
| Post subject: | Re: H25A Extractors |
Joe wrote: I paid $425 for J20 ones so $495 for them is a bargain Were did you buy the J20A extractors from? |
|
| Author: | tanshi [ Tue Apr 03, 2012 11:48 am ] |
| Post subject: | Re: H25A Extractors |
you can buy j20 extractors from hurricane headers. would be interested in selling you standard J20 manifold of you go to extractors? |
|
| Author: | atari4x4 [ Tue Apr 03, 2012 11:55 am ] |
| Post subject: | Re: H25A Extractors |
tanshi wrote: you can buy j20 extractors from hurricane headers. would be interested in selling you standard J20 manifold of you go to extractors? wanna swap some extractors for a stock manifold?  
|
|
| Author: | tanshi [ Tue Apr 03, 2012 12:00 pm ] |
| Post subject: | Re: H25A Extractors |
dunno about swap, but would be happy to subsidise some extractors in exchange |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|