auszookers.com
https://auszookers.com/forum/

GV Torque converter help!!!!!!!!!!
https://auszookers.com/forum/viewtopic.php?f=5&t=32817		 Page 1 of 1
Author:  twitchy [ Tue May 22, 2012 9:26 pm ]
Post subject:  GV Torque converter help!!!!!!!!!!
Does anyone know exactly how far back into the bell housing the GV Torque converter should sit????????? Can only get it to go back app. 15mm from the lip of the bell housing to the top of the nut on the converter ( where the flex plate bolts to), seems to be as far as I can get it to go...... only thing holding me up to getting the motor back in...
Author:  Scrawny [ Wed May 23, 2012 4:33 am ]
Post subject:  Re: GV Torque converter help!!!!!!!!!!
Without ever having done one I'd say it should go in a bit further. Some converters take quite a few turns to seat properly
Author:  twitchy [ Wed May 23, 2012 5:28 am ]
Post subject:  Re: GV Torque converter help!!!!!!!!!!
I though so to but after an hour of rooting around & spinning it like a record that's all I can get.........
Author:  christover1 [ Wed May 23, 2012 9:02 am ]
Post subject:  Re: GV Torque converter help!!!!!!!!!!
I took ages to get mine to go in.
What worked for me was:
Bolting converter loosely to motor,
than after assembly,
tightening up through inspection plate hole.

There is a topic on here somewhere that helped me sort it out.
Author:  christover1 [ Wed May 23, 2012 9:10 am ]
Post subject:  Re: GV Torque converter help!!!!!!!!!!
Found it viewtopic.php?f=5&t=27129&p=484094&hilit=torque+converter#p484094
Author:  twitchy [ Wed May 23, 2012 4:13 pm ]
Post subject:  Re: GV Torque converter help!!!!!!!!!!
Awesome guys thanks, I have measured both distances & seems like it will be o.k. but I will try a test bolt up before the state or origin tonight!!
Author:  twitchy [ Wed May 23, 2012 8:35 pm ]
Post subject:  Re: GV Torque converter help!!!!!!!!!!
Well I fucked that!!!!!!!!!!!!! Anyone got a spare GV torque converter they want to sell????? Stupid fuck I am....... :oops:
Author:  twitchy [ Thu May 24, 2012 4:44 pm ]
Post subject:  Re: GV Torque converter help!!!!!!!!!!
All good I have sorted the Torque converter & have it installed CORRECTLY this time, gave the snout a little massage today & checked it with the verniers & it all turns nicely so lets see what happens this time. attempt 3 to bolt the motor back in....... pompoms
Author:  Scrawny [ Thu May 24, 2012 4:46 pm ]
Post subject:  Re: GV Torque converter help!!!!!!!!!!
What did you do wrong?
Author:  twitchy [ Thu May 24, 2012 4:57 pm ]
Post subject:  Re: GV Torque converter help!!!!!!!!!!
Never seated the Torque converter properly & it distorted the end a we tad......... That's now sorted & sitting all the way in so another night in the garage on the floor for my poor ancient bones.. :P
Author:  Scrawny [ Thu May 24, 2012 5:02 pm ]
Post subject:  Re: GV Torque converter help!!!!!!!!!!
Must be bloody cold out there too! Might need a beer or 3 to keep you company
Author:  twitchy [ Thu May 24, 2012 8:46 pm ]
Post subject:  Re: GV Torque converter help!!!!!!!!!!
Note for others!!!!!!!!Torque converter must sit back at least 30mm from the front edge of the bell housing!!!!! Otherwise you will have grief like me!!!
Author:  christover1 [ Thu May 24, 2012 8:51 pm ]
Post subject:  Re: GV Torque converter help!!!!!!!!!!
3 days to get torque converter to connect properly,
sounds right to me :oops:
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/