Hey guys, how the hell do you get this black thing off the shifter???
| auszookers.com https://auszookers.com/forum/ |
|
| How does this thing come off??? https://auszookers.com/forum/viewtopic.php?f=5&t=33064 |
Page 1 of 2 |
| Author: | Scales [ Fri Jun 01, 2012 4:09 pm ] |
| Post subject: | How does this thing come off??? |
Hey guys, how the hell do you get this black thing off the shifter???
|
|
| Author: | Bruce [ Fri Jun 01, 2012 4:12 pm ] |
| Post subject: | Re: How does this thing come off??? |
Ya don't AFAIK. |
|
| Author: | Scales [ Fri Jun 01, 2012 4:13 pm ] |
| Post subject: | Re: How does this thing come off??? |
then how would one replace the boot, spring, etc.... |
|
| Author: | Joe [ Fri Jun 01, 2012 4:19 pm ] |
| Post subject: | Re: How does this thing come off??? |
Bruce wrote: Ya don't AFAIK. Correct they are glued on Boot stretches over the top from what i remember 
|
|
| Author: | Scales [ Fri Jun 01, 2012 4:21 pm ] |
| Post subject: | Re: How does this thing come off??? |
aggggggg best suggestion for getting it off without destroying it? i need to get the boot and crap off so i can bend it. |
|
| Author: | SierraDan [ Fri Jun 01, 2012 4:22 pm ] |
| Post subject: | Re: How does this thing come off??? |
Grinder. Put a slice down it and pry it off. The boot will slide it off though. |
|
| Author: | Bruce [ Fri Jun 01, 2012 4:23 pm ] |
| Post subject: | Re: How does this thing come off??? |
It's a tight fit but they come off. Let the rubber invert if that makes sense? |
|
| Author: | Scales [ Fri Jun 01, 2012 4:27 pm ] |
| Post subject: | Re: How does this thing come off??? |
well the rubber wont even go past the tiniest little lip on the shaft, its pretty stiff, cant see it stretching AT ALL. have these been cut off before? |
|
| Author: | Bruce [ Fri Jun 01, 2012 4:27 pm ] |
| Post subject: | Re: How does this thing come off??? |
Never cut any of the ones I have taken off. |
|
| Author: | Scales [ Fri Jun 01, 2012 4:28 pm ] |
| Post subject: | Re: How does this thing come off??? |
it has to come off somehow or the metal clip and spring cant be replaced ever. |
|
| Author: | Scales [ Fri Jun 01, 2012 4:29 pm ] |
| Post subject: | Re: How does this thing come off??? |
Bruce wrote: Never cut any of the ones I have taken off. are you talking about the rubber? or the solid black thing in the pic? |
|
| Author: | atari4x4 [ Fri Jun 01, 2012 4:31 pm ] |
| Post subject: | Re: How does this thing come off??? |
the solid black thing (shifter) is rubber filled & bonded to the shifter shaft for NVH dampening |
|
| Author: | Scales [ Fri Jun 01, 2012 4:34 pm ] |
| Post subject: | Re: How does this thing come off??? |
so i cant get it off then. I need to heat the shaft up but im worried about destroying the boot. |
|
| Author: | SierraDan [ Fri Jun 01, 2012 4:37 pm ] |
| Post subject: | Re: How does this thing come off??? |
The boot WILL come off. Pull harder, it won't rip. |
|
| Author: | Bruce [ Fri Jun 01, 2012 5:16 pm ] |
| Post subject: | Re: How does this thing come off??? |
SierraDan wrote: The boot WILL come off. Pull harder, it won't rip. x2 |
|
| Author: | Fatzook [ Fri Jun 01, 2012 5:17 pm ] |
| Post subject: | Re: How does this thing come off??? |
The boot slides over the thick black bit. To replace the spring, you cut the old one off, and slide the new one down over the thick black section. It will take some force. If you aren't sure, try and slide the new one on before you cut the old one off. The locking collar stays. |
|
| Author: | Scales [ Fri Jun 01, 2012 5:19 pm ] |
| Post subject: | Re: How does this thing come off??? |
okay im just leaving it as is for now, im goin crazy on it and i think im just making it worse for later. tried using 3 small screwdrivers to lever it off too. it seems to handle a bit of heat ok, so ill see what happens |
|
| Author: | zooky08 [ Fri Jun 01, 2012 5:32 pm ] |
| Post subject: | Re: How does this thing come off??? |
Turn the boot inside out then pull it offs |
|
| Author: | Scales [ Fri Jun 01, 2012 5:38 pm ] |
| Post subject: | Re: How does this thing come off??? |
yeah tried that, its really really really really tight. ill re-visit it tomorrow, im done with it for now. at least the bulk of the t-case swap is done. |
|
| Author: | zooky08 [ Fri Jun 01, 2012 5:48 pm ] |
| Post subject: | Re: How does this thing come off??? |
Soak it in hot water? |
|
| Author: | cairns27 [ Fri Jun 01, 2012 5:57 pm ] |
| Post subject: | Re: How does this thing come off??? |
Try dish washing liquid. bye |
|
| Author: | fire60 [ Sat Jun 02, 2012 5:17 am ] |
| Post subject: | Re: How does this thing come off??? |
When I heated mine to bend it after a body lift, I wrapped a wet rag around the hollow part with the rubber insert to stop it burning. This worked ok. I assume you are heating the stick after a B/L?? |
|
| Author: | twitchy [ Sat Jun 02, 2012 5:55 am ] |
| Post subject: | Re: How does this thing come off??? |
Jesus lads, ya wanna squeeze the big black bit through the tiny hole????????  Bahahahaha, try KY then 
|
|
| Author: | whincup [ Sat Jun 02, 2012 6:48 am ] |
| Post subject: | Re: How does this thing come off??? |
twitchy wrote: Jesus lads, ya wanna squeeze the big black bit through the tiny hole???????? Bahahahaha, try KY then i was having a laugh reading this thread  thinking, they need lube... but seriously, try a bit of ky, or vaseline, or something along those lines...
|
|
| Author: | Scales [ Sat Jun 02, 2012 9:22 am ] |
| Post subject: | Re: How does this thing come off??? |
had another go this morning, the boot aint coming off without destroying it. but its withstanding the blowtorch nicely anyway. so ill just keep at it. its not for a bodylift, just did an sj case swap. |
|
| Author: | want33s [ Sat Jun 02, 2012 9:26 am ] |
| Post subject: | Re: How does this thing come off??? |
NT transfer shifters don't have the rubber in the stick. May be easier to use one of them. |
|
| Author: | SierraDan [ Sat Jun 02, 2012 9:52 am ] |
| Post subject: | Re: How does this thing come off??? |
I might even have one Scales.. |
|
| Author: | wolf_rt [ Sat Jun 02, 2012 11:43 am ] |
| Post subject: | Re: How does this thing come off??? |
i used dishwashing liquid to get a new boot on, and cut the old one off |
|
| Author: | Scales [ Sat Jun 02, 2012 12:06 pm ] |
| Post subject: | Re: How does this thing come off??? |
well i got it off..... snapped the whole shaft into 3 pieces whilst bending... FUCK!!!!! |
|
| Author: | Teracis [ Sat Jun 02, 2012 10:27 pm ] |
| Post subject: | Re: How does this thing come off??? |
Scales wrote: well i got it off..... snapped the whole shaft into 3 pieces whilst bending... FUCK!!!!! Get the welder out! How bloody much were you trying to bend the thing? I bent a gearstick enough to make it work with a BL with a near empty gas bottle, a hammer and a block of wood and had no dramas, you must have been going pretty bloody hard! |
|
| Page 1 of 2 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|