auszookers.com
https://auszookers.com/forum/

wiring questions please help
https://auszookers.com/forum/viewtopic.php?f=5&t=33365		 Page 1 of 1
Author:  tonka_tuff [ Tue Jun 12, 2012 5:26 pm ]
Post subject:  wiring questions please help
ok so i have bought a 4 speed auto with wiring computer radiator everything needed just wondering if anyone can help me with the wiring side as im a noob lol i havent got any pics yet as i havent picked up the box ( on friday) has anyone done this swap before? its a vitara 4 speed onto a vitara carby motor..

all help appreciated thanks!

josh.
Author:  Scrawny [ Tue Jun 12, 2012 6:25 pm ]
Post subject:  Re: wiring questions please help
Why the 4 speed? I'm not even sure this mate is possible?
Author:  tonka_tuff [ Tue Jun 12, 2012 6:43 pm ]
Post subject:  Re: wiring questions please help
cause it has overdrive and has the 4th gear should cope with 31's easier.. heard a couple people have done it and 2 stroker says it can be done.. so hope so.. haha i think ive gotta wire up some cables to the vss or something but as i said im a noob at wiring..
Author:  royce [ Tue Jun 12, 2012 7:39 pm ]
Post subject:  Re: wiring questions please help
I am pretty good with wiring and certainly there is nothing in a 1.6 vit that scares me but I wouldn't be keen on doing this to an efi vit, its not going to work on a carby at all, there are signals the trans ecu are looking for from the engine ecu that you don't have and dont have any way to replicate.

your only way out is to look at one of them aftermarket shift controllers that turn it into a manual shift job
Author:  oozuk [ Tue Jun 12, 2012 7:47 pm ]
Post subject:  Re: wiring questions please help
tonka_tuff wrote:
ok so i have bought a 4 speed auto with wiring computer radiator everything needed just wondering if anyone can help me with the wiring side as im a noob lol i havent got any pics yet as i havent picked up the box ( on friday) has anyone done this swap before? its a vitara 4 speed onto a vitara carby motor..

all help appreciated thanks!

josh.


I'm doubtful you will find a solution to the wiring side of things but if you do i also would be very interested in the same setup in mine
Author:  tonka_tuff [ Tue Jun 12, 2012 9:19 pm ]
Post subject:  Re: wiring questions please help
well that sucks.. owell ill guess ill be chasing another good manual box and transfer then.. ha thanks guys! wish it could be done though.. would be so awesome!!
Author:  Scrawny [ Wed Jun 13, 2012 4:38 am ]
Post subject:  Re: wiring questions please help
tonka_tuff wrote:
well that sucks.. owell ill guess ill be chasing another good manual box and transfer then.. ha thanks guys! wish it could be done though.. would be so awesome!!


Well don't just give up yet. Pm 2stroker and do some asking of him.
Author:  jonno_racing [ Wed Jun 13, 2012 8:05 am ]
Post subject:  Re: wiring questions please help
manual controlled 4 speed auto = win. that's whats going in my next truck.
Author:  sogone [ Wed Jun 13, 2012 9:24 am ]
Post subject:  Re: wiring questions please help
And how are you achieving that?
Author:  JrZook [ Wed Jun 13, 2012 11:11 am ]
Post subject:  Re: wiring questions please help
Don't give up sooo quick! Anything can be solved and made to work.

The main AW4 auto TCM requirements are:

-Vehicle speed sensor (VSS) [Have a look at mine or Damo's threads on how to make one to suit you speedo cluster]
-Throttle position sensor (TPS) [Im sure you could scab one from the wreckers and adapt it to the throttle shaft on your carby]
-Engine coolant sensor (ECT) [You could find another from the wreckers and tap it into the manifold next to your sender for the temp gauge]

Sensor wise its doable. The other thing you will require is a circuit to read and interpret the sensor outputs to suit the TCM. This is what I'm currently working on for a few board members and will end up with a solution not too far away.
Author:  JrZook [ Wed Jun 13, 2012 11:12 am ]
Post subject:  Re: wiring questions please help
Ps make sure you get the TCM plug with it!
Author:  oozuk [ Thu Jun 14, 2012 7:34 pm ]
Post subject:  Re: wiring questions please help
JrZook wrote:
Don't give up sooo quick! Anything can be solved and made to work.

The main AW4 auto TCM requirements are:

-Vehicle speed sensor (VSS) [Have a look at mine or Damo's threads on how to make one to suit you speedo cluster]
-Throttle position sensor (TPS) [Im sure you could scab one from the wreckers and adapt it to the throttle shaft on your carby]
-Engine coolant sensor (ECT) [You could find another from the wreckers and tap it into the manifold next to your sender for the temp gauge]

Sensor wise its doable. The other thing you will require is a circuit to read and interpret the sensor outputs to suit the TCM. This is what I'm currently working on for a few board members and will end up with a solution not too far away.


I'm holding my breath waiting for you to do this, I REALLY REALLY REALLY REALLY hope you pull this off. I'll be ready with the cash if you do
Author:  sleeperzook [ Thu Jun 14, 2012 9:09 pm ]
Post subject:  Re: wiring questions please help
Mega squirt do an I/O board that's been used as a trans controller with great success, but if you're not confident with wiring I think it would be a nightmare for you.....
Author:  JrZook [ Thu Jun 14, 2012 10:24 pm ]
Post subject:  Re: wiring questions please help
oozuk wrote:
JrZook wrote:
Don't give up sooo quick! Anything can be solved and made to work.

The main AW4 auto TCM requirements are:

-Vehicle speed sensor (VSS) [Have a look at mine or Damo's threads on how to make one to suit you speedo cluster]
-Throttle position sensor (TPS) [Im sure you could scab one from the wreckers and adapt it to the throttle shaft on your carby]
-Engine coolant sensor (ECT) [You could find another from the wreckers and tap it into the manifold next to your sender for the temp gauge]

Sensor wise its doable. The other thing you will require is a circuit to read and interpret the sensor outputs to suit the TCM. This is what I'm currently working on for a few board members and will end up with a solution not too far away.


I'm holding my breath waiting for you to do this, I REALLY REALLY REALLY REALLY hope you pull this off. I'll be ready with the cash if you do


Ill be probing a vit out satde. So I'll be able to get all the info out I need to sort this thing out. ;)

Dan
Author:  2stroker [ Thu Jun 14, 2012 11:15 pm ]
Post subject:  Re: wiring questions please help
tonka_tuff wrote:
cause it has overdrive and has the 4th gear should cope with 31's easier.. heard a couple people have done it and 2 stroker says it can be done.. so hope so.. haha i think ive gotta wire up some cables to the vss or something but as i said im a noob at wiring..


This is what I was talking about when I said it could be done, there are some very smart people playing with this at the moment and I am confident they will get this to work.
Author:  oozuk [ Fri Jun 15, 2012 11:51 am ]
Post subject:  Re: wiring questions please help
JrZook wrote:
oozuk wrote:
JrZook wrote:
Don't give up sooo quick! Anything can be solved and made to work.

The main AW4 auto TCM requirements are:

-Vehicle speed sensor (VSS) [Have a look at mine or Damo's threads on how to make one to suit you speedo cluster]
-Throttle position sensor (TPS) [Im sure you could scab one from the wreckers and adapt it to the throttle shaft on your carby]
-Engine coolant sensor (ECT) [You could find another from the wreckers and tap it into the manifold next to your sender for the temp gauge]

Sensor wise its doable. The other thing you will require is a circuit to read and interpret the sensor outputs to suit the TCM. This is what I'm currently working on for a few board members and will end up with a solution not too far away.


I'm holding my breath waiting for you to do this, I REALLY REALLY REALLY REALLY hope you pull this off. I'll be ready with the cash if you do


Ill be probing a vit out satde. So I'll be able to get all the info out I need to sort this thing out. ;)

Dan


Dan :youdaman: :youdaman: :youdaman: :youdaman: :youdaman:
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/