| auszookers.com https://auszookers.com/forum/ |
|
| NT ignition Coil wiring https://auszookers.com/forum/viewtopic.php?f=5&t=33564 |
Page 1 of 1 |
| Author: | TryHard [ Wed Jun 20, 2012 9:52 pm ] |
| Post subject: | NT ignition Coil wiring |
hey guys well i got my NT Suzuki abit wet long story short after spraying some wd40 i had the car running but then it stalled seems im getting no spark from the ignition Coil now i had a look and its quite different to a WT coil dont know if its just this car or its all NTs but it seems to have a Resistor that was smoking basically what i need is photos of a NT ignition coil and or better yet wiring diagram Because i cant remember what goes where  any help would be great thanks
|
|
| Author: | matty_wall [ Wed Jun 20, 2012 10:13 pm ] |
| Post subject: | Re: NT ignition Coil wiring |
You'll find a drover wiring diagram here http://www.suzukiinfo.com/ |
|
| Author: | TryHard [ Wed Jun 20, 2012 10:14 pm ] |
| Post subject: | Re: NT ignition Coil wiring |
matty_wall wrote: thanks il take a look should help a bit |
|
| Author: | want33s [ Wed Jun 20, 2012 10:23 pm ] |
| Post subject: | Re: NT ignition Coil wiring |
Resistor smoking? Sounds like 1.0 electrics not 1.3 |
|
| Author: | TryHard [ Wed Jun 20, 2012 10:30 pm ] |
| Post subject: | Re: NT ignition Coil wiring |
it is a 1.0 lol NT LWB |
|
| Author: | TryHard [ Wed Jun 20, 2012 10:41 pm ] |
| Post subject: | Re: NT ignition Coil wiring |
Wants 33s i saw u saying something about a Ballast Resistor i think thats what was smoking it was mounted on the coil braket with a few leads going to it .. |
|
| Author: | want33s [ Wed Jun 20, 2012 11:11 pm ] |
| Post subject: | Re: NT ignition Coil wiring |
You should be able to buy a new ballast at any decent autoparts shop. Lots of older cars have them especially jap stuff so if there are old hiluxes/datsuns etc around your area check them out. Alternatively: Throw away the ballast and fit a 1.3 electronic dissy and coil. |
|
| Author: | TryHard [ Wed Jun 20, 2012 11:51 pm ] |
| Post subject: | Re: NT ignition Coil wiring |
i have a 1.3 electronic dissy does it bolt right up ? |
|
| Author: | TryHard [ Wed Jun 20, 2012 11:51 pm ] |
| Post subject: | Re: NT ignition Coil wiring |
i have a 1.3 electronic dissy does it bolt right up ? and does the ballast need to be a specific size ? |
|
| Author: | want33s [ Thu Jun 21, 2012 7:32 am ] |
| Post subject: | Re: NT ignition Coil wiring |
1.3 dissy bolts straight into a 1.0 or 1.3 engine. 1.3 dissy needs full 12V so remove the ballast as it reduces power to points down to about 7.5V. |
|
| Author: | TryHard [ Thu Jun 21, 2012 11:20 pm ] |
| Post subject: | Re: NT ignition Coil wiring |
ok well still scratching my head over this one ... this is what iv got to Black and white stripe goes to ballast then to + on coil blue wire from back of dizzy goes to - on coil has some sort of reg on it ;S yellow and white stripe i think goes to positive on coil .. seems to be ignition ... then i have red with white stripe ? and someone also had another earth going out of back of dizzy to fire wall Help please haha photos of NT coil with wires could help me alot please |
|
| Author: | 303zuke [ Fri Jun 22, 2012 11:19 am ] |
| Post subject: | Re: NT ignition Coil wiring |
It's not NT you want, it's 1.0lt. 1.3lt NT will be different to what you have. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|