auszookers.com
https://auszookers.com/forum/

Creeper Vs Hiem Joints
https://auszookers.com/forum/viewtopic.php?f=5&t=3376		 Page 1 of 1
Author:  steve [ Wed Nov 19, 2008 11:36 pm ]
Post subject:  Creeper Vs Hiem Joints
you know, you don't have to say anything on auszookers, but anything you say, can and will be used as evidence on google in their search engines :wink:

=====

All my stock control arm bushes are flogged out and I want some new joints and would love these creeper joints, but they are $84 each which is getting up there because i want atleast 4 to start with. possibly 8. ( they were $65 before the dollar went crap. I knew i should have bought them before)

So just wondering if hiem joints are cheeper? I'm having trouble finding them on the net.

Image
Author:  royce [ Wed Nov 19, 2008 11:44 pm ]
Post subject:  Re: Creeper Vs Hiem Joints
yes they are massively, I can get em cheap as but apprently they are shit, but any bearing place will have good ones
Author:  TZAR [ Wed Nov 19, 2008 11:56 pm ]
Post subject:  Re: Creeper Vs Hiem Joints
http://stores.ebay.com/QS-Components_5- ... idZ2QQtZkm

http://www.dauntlessmotors.com/Mounting ... mounts.htm

or locally CBC

http://www.conbear.com/sliding_bearings.htm
Author:  steve [ Thu Nov 20, 2008 12:20 am ]
Post subject:  Re: Creeper Vs Hiem Joints
thanks jock, yer i looked at that site but didn;t see their ebay stuff.

$181 US for 8, plus shipping.... so might be $450
Author:  TZAR [ Thu Nov 20, 2008 12:30 am ]
Post subject:  Re: Creeper Vs Hiem Joints
http://cgi.ebay.com/ebaymotors/4-LINK-K ... QQtcZphoto

$127 for 8 and then you just weld up some control arms from 1 1/4 tube that has been strengthened and keep your old arms as spares ;_0
Author:  royce [ Thu Nov 20, 2008 12:36 am ]
Post subject:  Re: Creeper Vs Hiem Joints
they look like the shit ones to me, I'll find out what ours are worth and you can decide if you want to have a go at em

factor big money for something to cut the thread into the arms too

/bright idea

ive always thought about getting the bits that make up a johnny joint cast in urethane :wink: I reckon if somebody can machine the bits from steel for one to fit in 40nb or something then knock a few out that can be clamped together with the mounting bolt it would work better than urethane and cheaper than heims
Author:  TZAR [ Thu Nov 20, 2008 12:39 am ]
Post subject:  Re: Creeper Vs Hiem Joints
that last one is for budget ones that come with weld in threads ( like a super nutsert) for the steel tmake your own new arms. rated at 18000 pounds ( 9000kgs)

The dearer ones are chrome moly higher quality ones.
Author:  steve [ Thu Nov 20, 2008 12:40 am ]
Post subject:  Re: Creeper Vs Hiem Joints
royce wrote:
ive always thought about getting the bits that make up a johnny joint cast in urethane :wink: I reckon if somebody can machine the bits from steel for one to fit in 40nb or something then knock a few out that can be clamped together with the mounting bolt it would work better than urethane and cheaper than heims


ya lost me, can you do a noob cad drawing of that?
Author:  royce [ Thu Nov 20, 2008 12:51 am ]
Post subject:  Re: Creeper Vs Hiem Joints
Image
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/