| auszookers.com https://auszookers.com/forum/ |
|
| Bearing went Bang https://auszookers.com/forum/viewtopic.php?f=5&t=33855 |
Page 1 of 2 |
| Author: | bogga [ Tue Jul 03, 2012 7:53 pm ] |
| Post subject: | Bearing went Bang |
Driving around today, started hearing a slight grinding noise and Bang??????? Got home and found this on the front drivers side    Check out the stub axle.........calling Boggomobile.........do you have one?  It was real dirty in there so I suspect mud & water is the culprit. |
|
| Author: | atari4x4 [ Tue Jul 03, 2012 8:06 pm ] |
| Post subject: | Re: Bearing went Bang |
a slight grinding noise.... are you deaf?  pm wants33 for a spare |
|
| Author: | zooky08 [ Tue Jul 03, 2012 8:21 pm ] |
| Post subject: | Re: Bearing went Bang |
Have done this twice. You must be deaf it doesn't sound good at all.
|
|
| Author: | bogga [ Tue Jul 03, 2012 8:26 pm ] |
| Post subject: | Re: Bearing went Bang |
Give me a break........stereo was cranked |
|
| Author: | JrZook [ Tue Jul 03, 2012 8:33 pm ] |
| Post subject: | Re: Bearing went Bang |
bogga wrote: Give me a break........stereo was cranked Well done! |
|
| Author: | bogga [ Tue Jul 03, 2012 8:34 pm ] |
| Post subject: | Re: Bearing went Bang |
but seriosly I thought it was mud in the front brakes after the run last weekend. It was just a slight tinny noise and not all the time? Havent driven it around too much till today and thought "I'll check that when I get home". Cheers atari I'll contact Wants33 if Boggomobile hasn't got one 
|
|
| Author: | worldo [ Wed Jul 04, 2012 8:55 am ] |
| Post subject: | Re: Bearing went Bang |
thats what my last one did. Unlucky mate. |
|
| Author: | BlueSuzy [ Wed Jul 04, 2012 9:06 am ] |
| Post subject: | Re: Bearing went Bang |
Awesome tech. How not to look after wheel bearings and result. |
|
| Author: | JrZook [ Wed Jul 04, 2012 10:33 am ] |
| Post subject: | Re: Bearing went Bang |
I still honestly don't know how you guys don't notice/feel/hear your bearings before they fully collapse like that! |
|
| Author: | Brenno [ Wed Jul 04, 2012 11:58 am ] |
| Post subject: | Re: Bearing went Bang |
She'll be right, wack it back in with some more grease... |
|
| Author: | Fatzook [ Wed Jul 04, 2012 12:07 pm ] |
| Post subject: | Re: Bearing went Bang |
I've re-built a few diffs that had nuggets like this. Its so easy to check for play in wheel bearings. Every time you change your oil, jack the car up, grab the tyre at 12 o'clock and 6 o'clock, and wobble it. If there is movement, check your bearings. |
|
| Author: | Brenno [ Wed Jul 04, 2012 1:18 pm ] |
| Post subject: | Re: Bearing went Bang |
Fatzook wrote: I've re-built a few diffs that had nuggets like this. Its so easy to check for play in wheel bearings. Every time you change your oil, jack the car up, grab the tyre at 12 o'clock and 6 o'clock, and wobble it. If there is movement, check your bearings. The problem is, some dont last an oil change, especially in shitty muddy states.... 
|
|
| Author: | Fatzook [ Wed Jul 04, 2012 2:42 pm ] |
| Post subject: | Re: Bearing went Bang |
Brenno wrote: Fatzook wrote: I've re-built a few diffs that had nuggets like this. Its so easy to check for play in wheel bearings. Every time you change your oil, jack the car up, grab the tyre at 12 o'clock and 6 o'clock, and wobble it. If there is movement, check your bearings. The problem is, some dont last an oil change, especially in shitty muddy states.... If your bearings aren't lasting 10,000kms you have some serious issues! |
|
| Author: | want33s [ Wed Jul 04, 2012 2:59 pm ] |
| Post subject: | Re: Bearing went Bang |
I have a heap of spindles here. |
|
| Author: | bogga [ Wed Jul 04, 2012 9:54 pm ] |
| Post subject: | Re: Bearing went Bang |
Got one today from Boggomobile so all good. Something interesting I found today, pulled the other side apart this arv, not that anything seemed out of place here, and found that both seals, the one behind the bearing and the axle seal were both failing?? Will post some pics tomorrow. Now remembering it was only a little over a month ago these were replaced new on both sides. I purchased the bearing/seal kit off ebay and yes it was one of the cheaper ones (can all ready hear the "told you so"  )
|
|
| Author: | zooky08 [ Wed Jul 04, 2012 10:09 pm ] |
| Post subject: | Re: Bearing went Bang |
Might be a dump thing to ask but you did remember to pack the bearings |
|
| Author: | atari4x4 [ Wed Jul 04, 2012 10:11 pm ] |
| Post subject: | Re: Bearing went Bang |
JrZook wrote: I still honestly don't know how you guys don't notice/feel/hear your bearings before they fully collapse like that! bogga wrote: Give me a break........stereo was cranked
|
|
| Author: | worldo [ Wed Jul 04, 2012 10:18 pm ] |
| Post subject: | Re: Bearing went Bang |
ben i get my bearings from coastline bearings my old man has used them for ages nice guys very helpful |
|
| Author: | shep [ Wed Jul 04, 2012 10:19 pm ] |
| Post subject: | Re: Bearing went Bang |
my front wheel bearings have lasted longer then i have been a member of AZ. |
|
| Author: | worldo [ Wed Jul 04, 2012 10:28 pm ] |
| Post subject: | Re: Bearing went Bang |
thats because there non flammable haha |
|
| Author: | shep [ Wed Jul 04, 2012 10:32 pm ] |
| Post subject: | Re: Bearing went Bang |
no knob gobbler it is because i fit them properly, i bet you lot use a chisel and hammer to do the bearing nuts up. |
|
| Author: | JrZook [ Wed Jul 04, 2012 11:07 pm ] |
| Post subject: | Re: Bearing went Bang |
shep wrote: no knob gobbler it is because i fit them properly, i bet you lot use a rock to do the bearing nuts up.
|
|
| Author: | atari4x4 [ Wed Jul 04, 2012 11:33 pm ] |
| Post subject: | Re: Bearing went Bang |
 @ nob gobbler
|
|
| Author: | alien [ Thu Jul 05, 2012 12:16 am ] |
| Post subject: | Re: Bearing went Bang |
are you following the manual where its says to do them up motheruckingcrazy tight, back them off then do them up to 'snug' ? since mine were done like that i've not had an issue at all... when they were just "done up" they only lasted around 5-7,000km. |
|
| Author: | shep [ Thu Jul 05, 2012 7:24 am ] |
| Post subject: | Re: Bearing went Bang |
alien wrote: are you following the manual where its says to do them up motheruckingcrazy tight, back them off then do them up to 'snug' ? since mine were done like that i've not had an issue at all... when they were just "done up" they only lasted around 5-7,000km. or (from memory) 50flb - 0flb - 10 flb |
|
| Author: | alien [ Thu Jul 05, 2012 8:29 am ] |
| Post subject: | Re: Bearing went Bang |
^^ yeah that. |
|
| Author: | Scrawny [ Thu Jul 05, 2012 8:33 am ] |
| Post subject: | Re: Bearing went Bang |
Make sure the spindle surface, where the seal runs, is clean and smooth too. A rough, corroded surface will quickly chew out a seal |
|
| Author: | Brenno [ Thu Jul 05, 2012 8:43 am ] |
| Post subject: | Re: Bearing went Bang |
shep wrote: alien wrote: are you following the manual where its says to do them up motheruckingcrazy tight, back them off then do them up to 'snug' ? since mine were done like that i've not had an issue at all... when they were just "done up" they only lasted around 5-7,000km. or (from memory) 50flb - 0flb - 10 flb I do my as per gwagens suggestions first nut to 90flb then to 0flb the to 15flb second nut (outer) to 80flb. I now check then after every mud trip. Spindles are good condition too. Sometimes they will last, sometimes they won't, depends on what terrain I have been driving. |
|
| Author: | Jackson [ Thu Jul 05, 2012 8:55 am ] |
| Post subject: | Re: Bearing went Bang |
Brenno wrote: shep wrote: alien wrote: are you following the manual where its says to do them up motheruckingcrazy tight, back them off then do them up to 'snug' ? since mine were done like that i've not had an issue at all... when they were just "done up" they only lasted around 5-7,000km. or (from memory) 50flb - 0flb - 10 flb I do my as per gwagens suggestions first nut to 90flb then to 0flb the to 15flb second nut (outer) to 80flb. I now check then after every mud trip. Spindles are good condition too. Sometimes they will last, sometimes they won't, depends on what terrain I have been driving. The FSM says first nut up to 90flb spinning the hub, back to 0flb, then 15flb. Lock washer on. Lock nut up to 80flb |
|
| Author: | shep [ Thu Jul 05, 2012 9:39 am ] |
| Post subject: | Re: Bearing went Bang |
Haha memery was wrong but that is why I have a FSM in my tool box |
|
| Page 1 of 2 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|