auszookers.com
https://auszookers.com/forum/

water temperature gauge wiring
https://auszookers.com/forum/viewtopic.php?f=5&t=3578		 Page 1 of 1
Author:  Mike [ Wed Dec 17, 2008 8:58 pm ]
Post subject:  water temperature gauge wiring
i've got an electronic water temperature gauge and was wondering if i hooked it up to the factory sender whether it would give an accurate reading

Cheers
Author:  royce [ Thu Dec 18, 2008 12:54 am ]
Post subject:  Re: water temperature gauge wiring
no
Author:  Mike [ Thu Dec 18, 2008 2:17 am ]
Post subject:  Re: water temperature gauge wiring
ok is there anywhere in the manifold/block that i could fit another sender other than the original?
Author:  royce [ Thu Dec 18, 2008 2:24 am ]
Post subject:  Re: water temperature gauge wiring
yes
Author:  Scrawny [ Thu Dec 18, 2008 2:26 am ]
Post subject:  Re: water temperature gauge wiring
Full of helpful info tonite Royce!! :lol:
Author:  royce [ Thu Dec 18, 2008 2:28 am ]
Post subject:  Re: water temperature gauge wiring
I am attempting to frustrate Mike into searching or undoing things to see where water falls out of on the manifold :wink:
Author:  Mike [ Thu Dec 18, 2008 2:35 am ]
Post subject:  Re: water temperature gauge wiring
search? if i wanted to search i would ask this question on a different forum
and don't worry i've already tried the undo stuff to see if i can fit a sender thing but i thought there might be somewhere i haven't thought of yet
Author:  royce [ Thu Dec 18, 2008 3:12 am ]
Post subject:  Re: water temperature gauge wiring
nah next to teh sender if you have the hole or where the vacuum thing goes in

why have 2 gauges anyway?
Author:  Mike [ Thu Dec 18, 2008 3:18 am ]
Post subject:  Re: water temperature gauge wiring
so that thing with the hoses that screws into the manifold near the temp sender can be taken out?

well i've got a temperature gauge so why not use it plus i don't trust the factory one because it thats like 15mins to register anything
Author:  Rockhopper [ Thu Dec 18, 2008 11:06 am ]
Post subject:  Re: water temperature gauge wiring
Mike wrote:
i don't trust the factory one because it thats like 15mins to register anything


Don't want to sound like a smart arse, but might that be because you don't have a thermostat installed?
Author:  royce [ Thu Dec 18, 2008 12:12 pm ]
Post subject:  Re: water temperature gauge wiring
put the aftermarket sender in the standard hole than?
Author:  steve [ Thu Dec 18, 2008 12:22 pm ]
Post subject:  Re: water temperature gauge wiring
get a new standard sender from supercheap? and clean all the electronical connections?
Author:  royce [ Thu Dec 18, 2008 12:24 pm ]
Post subject:  Re: water temperature gauge wiring
cant get 1.3 senders, genuine only
Author:  Scrawny [ Thu Dec 18, 2008 12:25 pm ]
Post subject:  Re: water temperature gauge wiring
steve wrote:
electronical


Is that even a word??? :P
Author:  steve [ Thu Dec 18, 2008 12:28 pm ]
Post subject:  Re: water temperature gauge wiring
aren't 1.3 and 1.6 senders the same? i bought one that i swapped between engines, i'm sure.
Author:  steve [ Thu Dec 18, 2008 12:30 pm ]
Post subject:  Re: water temperature gauge wiring
ScrawnC wrote:
steve wrote:
electronical


Is that even a word??? :P


yas knows what it meants, so it's all goods :)
Author:  royce [ Thu Dec 18, 2008 12:39 pm ]
Post subject:  Re: water temperature gauge wiring
no 1.6 in a sierra gauge reads wrong remember

unless they have started making them, or supercheap jsut gave you something to get rid of you

log into admin, I need lunch tips for round your area :wink:
Author:  Scrawny [ Thu Dec 18, 2008 12:43 pm ]
Post subject:  Re: water temperature gauge wiring
royce wrote:
I need lunch tips for round your area :wink:


We're having drinkies here at 3 if you like :lol: :D
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/