auszookers.com
https://auszookers.com/forum/

HOW DO I GET THE CRANK AND CAM PULLEYS OFF??? 1.3 Sierra
https://auszookers.com/forum/viewtopic.php?f=5&t=35939		 Page 1 of 1
Author:  Trypt [ Mon Sep 24, 2012 2:19 pm ]
Post subject:  HOW DO I GET THE CRANK AND CAM PULLEYS OFF??? 1.3 Sierra
This week im doing my big project of body work, rust repair and some engine maitenance.
Im replacing the timing belt, water pump and rad.

HOW DO I GET THE CRANK AND CAM PULLEYS OFF??? (so i can replace the seals)
is there a trick???

Thank you in advance
Author:  DarkHorse [ Mon Sep 24, 2012 2:34 pm ]
Post subject:  Re: NEEP HELP ASAP please
Several, search for "crank pulley breaker bar".
Author:  Trypt [ Mon Sep 24, 2012 2:43 pm ]
Post subject:  Re: NEEP HELP ASAP please
THank you very much
Author:  laurie [ Mon Sep 24, 2012 2:51 pm ]
Post subject:  Re: NEEP HELP ASAP please
i used a piece of square tube with two bolts through it for the cam pulley
and a long bar plus the starter for the crank ( TIGHT )
Author:  zukmeista [ Mon Sep 24, 2012 3:00 pm ]
Post subject:  Re: NEEP HELP ASAP please
Crank pulley, need a breaker bar about a meter long, put the car in 5th gear with handbrake on. Worked for me. You will also need a crank pulley remover tool thingy.
Author:  sideways [ Mon Sep 24, 2012 3:03 pm ]
Post subject:  Re: NEEP HELP ASAP please
I used a $70 electric rattle gun off ebay, it did it easy. :)
Author:  Trypt [ Mon Sep 24, 2012 3:31 pm ]
Post subject:  Re: NEEP HELP ASAP please
I think I might leave it for the mechanic... will it hurt if i don't do the seals now?
Author:  buzbox [ Mon Sep 24, 2012 3:36 pm ]
Post subject:  Re: NEEP HELP ASAP please
Crank pulley, Loosie on the ground or chassis, an extention pipe over Loosie's handle usually does the trick and turn the key. (oh Loosie is what I call my breaker bar)

Rattle gun for the cam pulley.

Undoing the bolts is the hard part.

Image
Author:  Trypt [ Mon Sep 24, 2012 8:38 pm ]
Post subject:  Re: HOW DO I GET THE CRANK AND CAM PULLEYS OFF??? 1.3 Sierr
Picture is inspiring but it will have to wait til I can get my hands on a rattle gun.
Author:  laurie [ Mon Sep 24, 2012 9:42 pm ]
Post subject:  Re: HOW DO I GET THE CRANK AND CAM PULLEYS OFF??? 1.3 Sierr
rattle gun not needed for cam pulley
i use this and a socket they are welded but bolted will also work
Image
Author:  DMAC [ Tue Sep 25, 2012 6:24 am ]
Post subject:  Re: HOW DO I GET THE CRANK AND CAM PULLEYS OFF??? 1.3 Sierr
Have you got a FSM?

To remove the camshaft pully you put a screwdriver in a hole around cylinder No.2 of the camshaft. Hold it still while you use a spanner to undo the bolt.
Author:  Trypt [ Tue Sep 25, 2012 11:13 am ]
Post subject:  Re: HOW DO I GET THE CRANK AND CAM PULLEYS OFF??? 1.3 Sierr
thanks for all the help fella's
Author:  abclarke [ Tue Sep 25, 2012 4:58 pm ]
Post subject:  Re: HOW DO I GET THE CRANK AND CAM PULLEYS OFF??? 1.3 Sierr
DMAC wrote:
Have you got a FSM?

To remove the camshaft pully you put a screwdriver in a hole around cylinder No.2 of the camshaft. Hold it still while you use a spanner to undo the bolt.


x2.

Its all in the FSM. Or just use a big podger if you dont have a screw driver big enough :)
Author:  Trypt [ Tue Sep 25, 2012 7:22 pm ]
Post subject:  Re: HOW DO I GET THE CRANK AND CAM PULLEYS OFF??? 1.3 Sierr
Not in with all the lingo. FSM?
Author:  Fatzook [ Tue Sep 25, 2012 8:05 pm ]
Post subject:  Re: HOW DO I GET THE CRANK AND CAM PULLEYS OFF??? 1.3 Sierr
Trypt wrote:
Not in with all the lingo. FSM?



Service manual. :wink:
Author:  Trypt [ Wed Sep 26, 2012 8:45 am ]
Post subject:  Re: HOW DO I GET THE CRANK AND CAM PULLEYS OFF??? 1.3 Sierr
Ahah i see :rofl:
Author:  HarryHoudini [ Wed Sep 26, 2012 10:28 am ]
Post subject:  Re: NEEP HELP ASAP please
sideways wrote:
I used a $70 electric rattle gun off ebay, it did it easy. :)


Any Link,can only see A$129 +. TIA
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/