Yes WT is worth it.
Yes you can get 1L ratios for WT diffs. They can be found in ANY WT Maruti. Must be a WT model though.
Yes, someone here sells new perches, and can even use his JIG to glue them on for you
| auszookers.com https://auszookers.com/forum/ |
|
| WT into NT conversion https://auszookers.com/forum/viewtopic.php?f=5&t=36092 |
Page 1 of 1 |
| Author: | Benchai [ Tue Oct 02, 2012 6:04 pm ] |
| Post subject: | WT into NT conversion |
I went wheeling at Levuka last weekend. I had made some 2" extended shackles and borrowed the young fella's 29's, and what a difference it made to clearance, but what a pig to drive, virtually nil lateral stability. Dropped driver's front wheel into a hollow down a hill and nearly fell over - luckily it was in a gully and I could put my arm out and save it. Not much fun to drive on the road either, so how much difference could I expect if I fitted WT diffs? I really like my f10A, but I don't think it would like higher diff ratios, so is there such an animal as WT diffs with 1.0L ratios, and if so are they a rare and sought after commodity? I can visualise the conversion, and recall seeing the brackets for sale somewhere, but is it worth the effort |
|
| Author: | Fatzook [ Tue Oct 02, 2012 6:09 pm ] |
| Post subject: | Re: WT into NT conversion |
| Yes WT is worth it. Yes you can get 1L ratios for WT diffs. They can be found in ANY WT Maruti. Must be a WT model though. Yes, someone here sells new perches, and can even use his JIG to glue them on for you
|
|
| Author: | Benchai [ Tue Oct 02, 2012 6:13 pm ] |
| Post subject: | Re: WT into NT conversion |
Fatzook wrote: :hey: Yes WT is worth it. Yes you can get 1L ratios for WT diffs. They can be found in ANY WT Maruti. Must be a WT model though. Yes, someone here sells new perches, and can even use his JIG to glue them on for you I did think it was you that sold them Mr Fat, so I think I might start the hunt. Can the centres in the 1.0 WT diffs be changed should I change to 1.6 down the track? |
|
| Author: | Fatzook [ Tue Oct 02, 2012 6:16 pm ] |
| Post subject: | Re: WT into NT conversion |
yep. WT 1.3, NT 1.3, and WT maruti are all interchangable. They also accept vitara front R&P's, so that opens up more gearing options should you be chasing reduction at a later date. I must stress that it is ONLY the wt maruti (4.11:1) that will fit a 1.3L housing. The NT maruti is identicle to your current diff in every way. |
|
| Author: | mrw82 [ Tue Oct 02, 2012 6:25 pm ] |
| Post subject: | Re: WT into NT conversion |
PM rhino, he had a pair for sale a while ago, may still have them. |
|
| Author: | Jackson [ Tue Oct 02, 2012 8:04 pm ] |
| Post subject: | Re: WT into NT conversion |
Fatzook wrote: Yes you can get 1L ratios for WT diffs. They can be found in ANY WT Maruti. Must be a WT model though. This is worth it too, atleast get something that is the same or lower geared than 1ltr, when I put the WT diffs in mine I used NT 3.9 centres and that was even annoyingly noticeable. |
|
| Author: | stockman [ Tue Oct 02, 2012 8:18 pm ] |
| Post subject: | Re: WT into NT conversion |
Brave putting your arm out to save the car. |
|
| Author: | Fatzook [ Tue Oct 02, 2012 8:19 pm ] |
| Post subject: | Re: WT into NT conversion |
stockman wrote: Brave putting your arm out to save the car. I'd risk a broken bone to save the taxi
|
|
| Author: | Benchai [ Tue Oct 02, 2012 9:16 pm ] |
| Post subject: | Re: WT into NT conversion |
stockman wrote: Brave putting your arm out to save the car. In hindsight probably right, but possible injury vs definite panel damage I guess it was just a natural reaction. Did get the help across the gully fairly quickly though  Mr Fat, can I get lockers to fit the Maruti diffs? |
|
| Author: | Fatzook [ Tue Oct 02, 2012 10:31 pm ] |
| Post subject: | Re: WT into NT conversion |
Benchai wrote: Mr Fat, can I get lockers to fit the Maruti diffs? Yep. For all intensive purposes, a WT maruti diff is the same as a WT sierra diff. Bearings, seals, lockers, axles etc etc. |
|
| Author: | KEENSY85 [ Wed Oct 03, 2012 9:07 pm ] |
| Post subject: | Re: WT into NT conversion |
Fatzook wrote: Benchai wrote: Mr Fat, can I get lockers to fit the Maruti diffs? Yep. For all intensive purposes, a WT maruti diff is the same as a WT sierra diff. Bearings, seals, lockers, axles etc etc. could u make a hybrid centre out of the wt ones and 1l ones beering in mind iv never seen a 1l 3rd member |
|
| Author: | Fatzook [ Wed Oct 03, 2012 9:24 pm ] |
| Post subject: | Re: WT into NT conversion |
KEENSY85 wrote: Fatzook wrote: Benchai wrote: Mr Fat, can I get lockers to fit the Maruti diffs? Yep. For all intensive purposes, a WT maruti diff is the same as a WT sierra diff. Bearings, seals, lockers, axles etc etc. could u make a hybrid centre out of the wt ones and 1l ones beering in mind iv never seen a 1l 3rd member No. The hemisphere, Crown wheel and Pinion are all much smaller in the 1L third. 1l is the same size as LJ50-80. |
|
| Author: | jdk81 [ Thu Oct 04, 2012 5:30 am ] |
| Post subject: | Re: WT into NT conversion |
WT maruti centres http://auszookers.com/forum/viewtopic.php?f=7&t=36129 |
|
| Author: | whincup [ Thu Oct 04, 2012 6:14 am ] |
| Post subject: | Re: WT into NT conversion |
the maruti diff centre combined with a 1L transfer case makes the car just about perfect on the road with 31's. my tired old 1.3L engine can still haul my maruti along at 100, more if it feels like it. |
|
| Author: | slowsierra [ Sat Oct 27, 2012 4:40 pm ] |
| Post subject: | Re: WT into NT conversion |
not sure if this is the right tread to but this in but its better then starting a new one. I have just started doing this conversion to my 1.3L LWB NT sierra. my question is would the diff ratios between the 1.3L NT and the 1.3L WT be the same? the reason i ask is cause the WT centre won't bolt up to drive shaft. what is the easiest fix, swap the diff centres or can you undo the nut on the diff flange and swap them over? what are the ratios of: 1L NT diffs 1.3L NT diffs 1.3L WT diffs Thanks greg |
|
| Author: | Teracis [ Sat Oct 27, 2012 5:44 pm ] |
| Post subject: | Re: WT into NT conversion |
You can change the flanges pretty easily, worst case if you don't have flanges to swap you can slot the hole on one (bolt still can't spin out because you've only slotted one flange). Afaik 1.3L NT = 3.9 ratio 1.3L WT = 3.7 ratio |
|
| Author: | jdk81 [ Sat Oct 27, 2012 6:50 pm ] |
| Post subject: | Re: WT into NT conversion |
Swap diff centres The NT front centre is 4 pin (which is better), the WT is 2 pin The NT ratios are also a little more useful (there is an annoying difference between 3.9 and 3.7, it isn't much, but you do notice it). Revving 5% higher is tolerable, revving 5% less than ideal is irritating, because you will be between 4th and 5th a hell of a lot! |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|