| auszookers.com https://auszookers.com/forum/ |
|
| jimnybits lift jimny problems https://auszookers.com/forum/viewtopic.php?f=5&t=36437 |
Page 1 of 1 |
| Author: | kristov [ Tue Oct 16, 2012 8:44 pm ] |
| Post subject: | jimnybits lift jimny problems |
hey well today i tryed fitting my new jimnybits lift and found 2 things witch made me stop and put back together  1.the shims u get to put into the bushes one fits perfectly with the bolts with no play but the closes other one had a little play in it. still alright to use?? 2. the top bush on the rear springs wont fit into the mount where its suppose to its about 2mm to big. do i cut the rubber down to fit? |
|
| Author: | zukenutter [ Tue Oct 16, 2012 9:11 pm ] |
| Post subject: | Re: jimnybits lift jimny problems |
 Lol I hate when witches fly in and stop me from fitting a lift. Just stirring, please ignore. Suggestions below kristov wrote: hey well today i tryed fitting my new jimnybits lift and found 2 things witch made me stop and put back together
1.the shims u get to put into the bushes one fits perfectly with the bolts with no play but the closes other one had a little play in it. still alright to use?? I assume we're talking about the metal sleeve in the centre of a urethane control arm bush, and the bolt that goes through it. If so I think unless there's loads of play it should be fine. Pack a heap of grease in there to stop it clunking. 2. the top bush on the rear springs wont fit into the mount where its suppose to its about 2mm to big. do i cut the rubber down to fit? The mount can probably be spread a little with a pinch bar or some pipe etc. Otherwise, use a jack to force it in. The urethane will give a bit, and again smear grease on it to help it slide in. |
|
| Author: | kristov [ Tue Oct 16, 2012 10:02 pm ] |
| Post subject: | Re: jimnybits lift jimny problems |
haha always get them two mixed up smartarse  anyhow i will try that tomorrow with alot a grease, other than them problems its relatively easy to change and the jimny bits coils a mean compared to stock 
|
|
| Author: | Scales [ Wed Oct 17, 2012 6:17 am ] |
| Post subject: | Re: jimnybits lift jimny problems |
top bush on SPRING? um are we talking about the shock? If we are... I had EPIC trouble getting that mofo in the rear mounts too. had to force it in with the jack, and even that was pretty damn difficult. took about 2 hours on its own to do that. Are they the rubber bushes that come with the shocks? |
|
| Author: | zukenutter [ Wed Oct 17, 2012 6:53 am ] |
| Post subject: | Re: jimnybits lift jimny problems |
Scales wrote: top bush on SPRING? um are we talking about the shock? If we are... I had EPIC trouble getting that mofo in the rear mounts too. had to force it in with the jack, and even that was pretty damn difficult. took about 2 hours on its own to do that. Are they the rubber bushes that come with the shocks? Oh yeah I forgot to question that... ?? |
|
| Author: | Scales [ Wed Oct 17, 2012 8:04 am ] |
| Post subject: | Re: jimnybits lift jimny problems |
oh good, i was hoping that.. Thought you might know something I didnt nutter. BTW, love the hot witch...... Legs FTW |
|
| Author: | kristov [ Wed Oct 17, 2012 8:10 am ] |
| Post subject: | Re: jimnybits lift jimny problems |
haha sorry yes shock i mean .... was in a rush  sorry for the confusion will try bending a little tomorrow and see if that helps if not get the jack out |
|
| Author: | JayKay [ Wed Oct 17, 2012 8:34 am ] |
| Post subject: | Re: jimnybits lift jimny problems |
Gave my rear shock mounts a to fit mine in, it did the trick.Good Luck with it |
|
| Author: | BertZook [ Wed Oct 17, 2012 12:09 pm ] |
| Post subject: | Re: jimnybits lift jimny problems |
I didnt have any issues when changing my rear shocks :/ is it something to do with bigger lift or wht? |
|
| Author: | zukenutter [ Wed Oct 17, 2012 12:12 pm ] |
| Post subject: | Re: jimnybits lift jimny problems |
Just the shock bushes I think. Different brands = different bushes. |
|
| Author: | zooky08 [ Wed Oct 17, 2012 12:17 pm ] |
| Post subject: | Re: jimnybits lift jimny problems |
My jb shock bushes were hard to get in. I was a bit dogy nd sanded them down until they fitted. |
|
| Author: | kristov [ Wed Oct 17, 2012 11:15 pm ] |
| Post subject: | Re: jimnybits lift jimny problems |
well after hours this arvo bashing around i finally got the rear shock and springs in  fingers crossed the fronts are easier
|
|
| Author: | zooky08 [ Thu Oct 18, 2012 6:55 am ] |
| Post subject: | Re: jimnybits lift jimny problems |
Disconnect all shocks and jack the car up and your coils should fall out. Rear is easier then the front to put coils in. |
|
| Author: | kristov [ Fri Oct 19, 2012 5:47 pm ] |
| Post subject: | Re: jimnybits lift jimny problems |
ok well i got it in all good now but it seems to be sitting alott higher than 2 inches when flexed the brake lines are pretty tight, hey jaykay what numbers where stamped on your JB 3 inch lift? |
|
| Author: | dirtydogz [ Sun Oct 21, 2012 5:09 am ] |
| Post subject: | Re: jimnybits lift jimny problems |
The jimnybits 2" lift will look high till it settles down, this is my jimny when I first fitted the 2" jimnybits lift + 205/75/15 m/t. http://www.bigjimny.com/ Attachment: DSCF0001 - Copy.JPG
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|