tried rhino's link?
it's 115mb so i'm guessing it's the whole manual... just not sure what year.
http://www.rhinoman.org/
| auszookers.com https://auszookers.com/forum/ |
|
| 1996 baleno G16B distributor model ecu pinout/wiring diag https://auszookers.com/forum/viewtopic.php?f=5&t=39242 |
Page 1 of 1 |
| Author: | kenny.G345 [ Mon Feb 25, 2013 9:09 pm ] |
| Post subject: | 1996 baleno G16B distributor model ecu pinout/wiring diag |
Hey all i am currently up to the fun part of wiring up my 1996 baleno G16B distributor model into my sierra and was wondering if anyone had an ECU pinout or wiring diagram??? Yes i have searched multiple times |
|
| Author: | losfer [ Tue Feb 26, 2013 8:02 pm ] |
| Post subject: | Re: 1996 baleno G16B distributor model ecu pinout/wiring dia |
i have the manual but too large to send via email .. |
|
| Author: | atari4x4 [ Tue Feb 26, 2013 8:25 pm ] |
| Post subject: | Re: 1996 baleno G16B distributor model ecu pinout/wiring dia |
have a suss of this one of Rhinoman's he posted the other day http://www.rhinoman.org/ |
|
| Author: | kenny.G345 [ Tue Feb 26, 2013 8:50 pm ] |
| Post subject: | Re: 1996 baleno G16B distributor model ecu pinout/wiring dia |
is there anyway you can get it to me losfer, like in sections? |
|
| Author: | atari4x4 [ Tue Feb 26, 2013 8:54 pm ] |
| Post subject: | Re: 1996 baleno G16B distributor model ecu pinout/wiring dia |
tried rhino's link? it's 115mb so i'm guessing it's the whole manual... just not sure what year. http://www.rhinoman.org/ |
|
| Author: | Rhinoman [ Wed Feb 27, 2013 8:37 am ] |
| Post subject: | Re: 1996 baleno G16B distributor model ecu pinout/wiring dia |
Have a look here: http://rhinopower.activeboard.com/t4537 ... to-vitara/ I think that is the same as the one that you have. |
|
| Author: | JrZook [ Wed Feb 27, 2013 10:44 am ] |
| Post subject: | Re: 1996 baleno G16B distributor model ecu pinout/wiring dia |
Hey James, Slightly off topic but is that Baleno 33910-60GB1 ECU also used in the J series engines? At a glance it looks awfully similar to the J18 architecture. |
|
| Author: | Rhinoman [ Wed Feb 27, 2013 6:37 pm ] |
| Post subject: | Re: 1996 baleno G16B distributor model ecu pinout/wiring dia |
All the early J series ECUs that I have seen have been Hitachi with 8-bit processors. |
|
| Author: | JrZook [ Wed Feb 27, 2013 10:22 pm ] |
| Post subject: | Re: 1996 baleno G16B distributor model ecu pinout/wiring dia |
Just dug it out. Its a 33920-57B4. EPROM 112043-0321. Apparently it was off a J18? Going by the pics in your link it has exactly the same hardware layout. Do they use VR for cam angle sensors? If so I'll have a go at tracing this one. |
|
| Author: | Rhinoman [ Wed Feb 27, 2013 11:18 pm ] |
| Post subject: | Re: 1996 baleno G16B distributor model ecu pinout/wiring dia |
33920-57B40 is for an early G16A 16V Vitara Auto with a Volume Air Flow meter. This is the ECU with the 42-pin Denso processor? The architecture is quite similar and the 57B40 does use a VR sensor. I'll drop you a PM later, I'm currently working on a Swift GTi with a faulty CAS input. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|