| auszookers.com https://auszookers.com/forum/ |
|
| what 16b exhaust to use https://auszookers.com/forum/viewtopic.php?f=5&t=40140 |
Page 1 of 1 |
| Author: | burls [ Mon Apr 08, 2013 8:49 pm ] |
| Post subject: | what 16b exhaust to use |
Just wondering what sort of exhaust/muffler/cat to run in the LJ Do 79 model rules apply or the engine year 93? |
|
| Author: | Fatzook [ Mon Apr 08, 2013 8:51 pm ] |
| Post subject: | Re: what 16b exhaust to use |
year of engine in QLD. You'll need a cat. Muffler choice is up to you, but obviously there are noise restrictions. |
|
| Author: | burls [ Mon Apr 08, 2013 9:02 pm ] |
| Post subject: | Re: what 16b exhaust to use |
thats what I heard but didnt want to believe it. What size works well with these engines, if it makes any difference its efi |
|
| Author: | Fatzook [ Mon Apr 08, 2013 9:06 pm ] |
| Post subject: | Re: what 16b exhaust to use |
burls wrote: thats what I heard but didnt want to believe it. What size works well with these engines, if it makes any difference its efi 2" press bent will be fine. Fit a chambered muffler, not a straight through one, and you'll be fine. |
|
| Author: | burls [ Sat Aug 03, 2013 5:07 pm ] |
| Post subject: | Re: what 16b exhaust to use |
Got all the bits to finish the exhaust this weekend. Is there a desired length from the extractors to the cat or doesnt it matter? |
|
| Author: | Gwagensteve [ Sat Aug 03, 2013 5:26 pm ] |
| Post subject: | Re: what 16b exhaust to use |
The closer the better. |
|
| Author: | burls [ Sat Aug 03, 2013 6:34 pm ] |
| Post subject: | Re: what 16b exhaust to use |
I was afraid of that, there's not a lot of room between the LJ rails. I'll see how I go - might be able to jam it up there |
|
| Author: | Teracis [ Sun Aug 04, 2013 2:04 pm ] |
| Post subject: | Re: what 16b exhaust to use |
When I built my exhaust the other week out of bits from both the Sierra and the stock exhaust I took from the baleno, I mounted the cat as close as I could get it to the extractors but up between the rails so that it wouldn't rip off, this may even be back behind or level with the transfer. Hopefully it's all good like that otherwise it will get torn off just by looking at it... |
|
| Author: | burls [ Sun Aug 04, 2013 6:32 pm ] |
| Post subject: | Re: what 16b exhaust to use |
Well I had slow progression as I said before there is not much room. Is there a smaller cat that I could use other than the vit one? |
|
| Author: | Gwagensteve [ Mon Aug 05, 2013 7:56 am ] |
| Post subject: | Re: what 16b exhaust to use |
Yes, for sure, but they get very pricey |
|
| Author: | droverdave [ Mon Aug 05, 2013 9:21 am ] |
| Post subject: | Re: what 16b exhaust to use |
How big is the one you are trying to fit? http://www.ebay.com.au/itm/2-High-Hi-Fl ... 3f2690cd30 Unfortuntaely it doesnt give a size, but if those are 2" pipes, then thats quite small overall. and only $110. |
|
| Author: | burls [ Mon Aug 05, 2013 7:55 pm ] |
| Post subject: | Re: what 16b exhaust to use |
I just good an answer back about the cat it's 6x3x11 compared with the vit one which is 7 1/2 x 4x13 so this might be the trick I wonder if the hi flow might be too trick for the 1.6 |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|